497495
25
Zoom out
Zoom in
Vorherige Seite
1/59
Nächste Seite
25
<When the installation plate is directly
mounted on the wall>
(1) Securely fit the installation plate onto the wall by
screwing it in the upper and lower parts to hook
up the indoor unit.
(2) Install the installation plate horizontally in the
wall.
(3) To mount the installation plate on a concrete wall
with anchor bolts, utilize the anchor bolt holes as
shown in the above figure.
CAUTION
When installing the installation plate with mount-
ing screw, do not use the anchor bolt hole.
Otherwise the unit may fall down and result in
personal injury and property damage.
CAUTION
Failure to firmly install the unit may result in per-
sonal injury and property damage if the unit falls.
In case of block, brick, concrete or similar type
walls, make holes in the wall.
Insert clip anchors for appropriate
U
mounting
screws.
NOTE :
Install the installation plate using 4 to 6 pieces of
mounting screw securing four corners with screws.
8-4-2. Electrical Work
(1) The supply voltage must be the same as the
rated voltage of the air conditioner.
(2) Prepare the power source for exclusive use with
the air conditioner.
CAUTION
Use power specified above table.
This appliance can be connected to the mains
in either of the following two ways.
(1) Connection to fixed wiring:
A switch or circuit breaker which disconnects
all poles and has a contact separation of at
least 3 mm must be incorporate in the fixed
wiring. An approved circuit breaker or
switches must be used.
(2) Connection with power supply plug:
Attach power supply plug with power cord and
plug it into wall outlet. An approved power
supply cord and plug must be used.
NOTE :
Perform wiring works so as to allow a generous
wiring capacity.
*
No adjustment is necessary.
Fig. 8-4-4
Installation plate
(Keep horizontal direction)
Anchor bolt
Projection
15mm
or less
5mm dia, hole
Clip anchor
5
Mounting screw Ø4 x 25
MODEL
RAS-07YKX
RAS-07YK-E
RAS-10YKX
RAS-11YKX
RAS-10YK-E
RAS-10YK-ES
RAS-10YK-HX
RAS-07YKX-T RAS-10YKX-T
RAS-07YK-ES
Power source 50Hz
*
220240V
~
Single-phase 50Hz
*
220V
~
Single-phase
Maximum running current 5A 7,5A 5A 7,5A
Plug socket & fuse rating 16A
Wiring 1mm
2
or more
25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Toshiba RAS-10YK-HX wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info