Bedienungsanleitung Toshiba RAS-12LAV-UL (Seite 3 von 12) (Englisch, Französisch, Spanisch)

497462

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

INDOOR UNIT DISPLAY

1 Hi POWER (Green)

2 FILTER (Orange)

3 PRE. DEF (Preheat/Defrost)

(Orange)

4 TIMER (Yellow)

5 OPERATION (Green)

6 RESET button

Press

FIX

: Move the louver to the

desired vertical direction.

Press

SWING

: To continuously swing

the louver automatically and press

again to stop.

For horizontal direction, adjust

manually.

AIR FLOW DIRECTION

Note:

• Do not move the louver manually by others.

• The louver may automation positioning by some operation mode.

ONE-TOUCH

AUTOMATIC OPERATION

To automatically select cooling, heating, or fan only operation

1. Press

MODE

: Select A.

2. Press

TEMP

: Set the desired temperature.

Press the “ONE-TOUCH” button for fully automated operation that is

customized to the typical consumer preferences in your region of the world.

The customized settings control temperature air ﬂ ow strength, air ﬂ ow

direction and other settings to provide you alternate contact with “ONE-

TOUCH” of the button. If you prefer other settings you can select from the

many other operating functions of your unit.

Press

ONE-TOUCH

: Start the operation.

REMOTE CONTROL

PREPARATION BEFORE USE

Preparing Filters

1. Open the air inlet grille and remove the air ﬁ lters.

2. Attach the ﬁ lters. (see detail in the accessory sheet).

Loading Batteries

1. Remove the battery cover.

2. Insert 2 new batteries (AAA type)

following the (+) and (–) positions.

Clock Setup

1. Push CLOCK

● by tip of the pencil.

If timer indication is ﬂ ashing, go to the next step 2.

2. Press

OFF

: adjust the time.

3. Press

SET

: Set the time.

Temperature Unit °F-°C Selection

1. Push and hold CHK ● button on the Remote

Control by the tip of the pencil, “00” will be

shown on the display.

2. Press

SLEEP

while pushing CHK ●.

Note: 1. Repeat above step to reset Remote

Control to be °F.

2. Operation mode and temperature

set will reset to initial setting after

change the temperature unit.

3. Default setting of Remote Control

from factory is °F.

PRESET

ONE-TOUCH

QUIET

SWING

TIMER

FILTER

CHK

˚C/˚F

CLOCK

OFF

CLR

SLEEP

SET

FIX Hi-POWER ECO

COMFORT

SLEEP

MODE

TEMP

FAN

1 Infrared signal emitter

2 Start/Stop button

3 Mode select button (MODE)

4 Temperature button (TEMP)

5 Fan speed button (FAN)

6 Swing louver button

(SWING)

7 Set louver button (FIX)

8 On timer button (ON)

9 Off timer button (OFF)

! Sleep timer button (SLEEP)

" Setup button (SET)

# Clear button (CLR)

$ Memory and Preset button

(PRESET)

% One-Touch button

(ONE-TOUCH)

& High power button

(Hi-POWER)

( Economy button (ECO)

) Quiet button (QUIET)

~ Comfort sleep button

(COMFORT SLEEP)

+ Filter reset button (FILTER)

, Clock Reset button (CLOCK)

- Check button (CHK)

REMOTE CONTROL A-B SELECTION

To separate using of remote control for each indoor unit in case of 2 air

conditioners are installed adjacent to each other.

Remote Control B Setup.

1. Press RESET button on the indoor unit to turn the air conditioner ON.

2. Point the remote control at the indoor unit.

3. Push and hold CHK

● button on the Remote Control by the tip of the

pencil. “00” will be shown on the display.

4. Press

MODE

while pushing CHK ●. “B” will show on the display and “00”

will disappear and the air conditioner will turn OFF. The Remote Control

B is memorized.

Note: 1. Repeat above step to reset Remote Control back to A.

2. Remote Control A have not “A” display.

3. Default setting of Remote Control from

factory is A.

SYSTEM CHARACTERISTICS

1. Three-minute time delay: To protect against frequent compressor starts.

2. Preheating operation: Warm up the unit for several minutes before

blowing warm air.

3. Warm air control: When the room temperature reaches the set

temperature, the fan speed is automatically reduced and the outdoor unit

will stop.

4. Automatic defrosting: Fans will stop during defrost operation.

5. Heating capacity: Heat is absorbed from outdoor and released into

the room. When the outdoor temperature is too low, use another

recommended heating apparatus in combination with the air conditioner.

6. Some minor cracking sound may occur when unit operating. This is

normal and is caused by expansion/contraction of plastic.

Note: Item 2 to 5 for Heating model

Air conditioner operating conditions

Temp.

Operation

Outdoor Temperature

Room

Temperature

Heating 5°F ~ 75°F (–15°C ~ 24°C) Less than 82°F (28°C)

Cooling 14°F ~ 115°F (–10°C ~ 46°C) 70°F ~ 90°F (21°C ~ 32°C)

Dry 14°F ~ 115°F (–10°C ~ 46°C) 62°F ~ 90°F (17°C ~ 32°C)

CLR

SLEEP

SET

“B” Display

“00” Display

1110650133-1-EN.indd 31110650133-1-EN.indd 3 1/4/10 3:50:57 PM1/4/10 3:50:57 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toshiba RAS-12LAV-UL Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info