Bedienungsanleitung Toshiba RAV-SM806KRT-E (Seite 14 von 24) (Englisch)

497453

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

–13–

 Operation section

Push each button to select a desired operation.

•

The control saves commands in memory and after the initial setting, there is no need for any additional

settings unless changes are desired. The air conditioner can be operated by pushing the

button.

button (Temperature set button)

Adjusts the set point.

Select the desired set point by pushing TEMP.

or TEMP. .

2 button (Timer set button)

Use to setup the timer.

3 button (Filter reset button)

Resets “ ” display after cleaning filter.

4 button (Test button)

Use only for service.

(During normal operation, do not use this button.)

5 button

When the button is pushed, the operation starts,

and it stops by pushing the button again.

When the operation has stopped, the operation

lamp and all the displays disappear.

6 Operation lamp

Green light illuminates when unit is on.

Although it flashes when the protection device is

operated or an error occurs.

7 button (Operation mode button)

Selects desired operation mode.

8 button (Fan speed button)

Selects the desired Fan speed.

9 button (Ventilation button)

Use when a power ventilation kit (locally procured)

is connected.

• If “ ” is displayed on the remote controller

when this button is pushed, no vent kit

connected.

button (Power save operation)

Use to initiate power saving mode.

button (Unit / Louver select button)

Selects a unit number (left) and louver number

(right).

UNIT:

Selects an indoor unit when multiple indoor units

are controlled with one remote controller.

LOUVER:

Selects a louver when setting louver lock or wind

direction adjustment independently.

button (Swing / Louver direction

button)

Selects automatic swing or setting the louver

direction.

◆ OPTION:

Remote controller sensor

Usually the temperature sensor of the indoor unit

senses the temperature. The temperature on the

surrounding of the remote controller can also be

sensed.

For details, contact the dealer from which you have

purchased the air conditioner.

5-1. Correct usage

When the air conditioner is used for the first time or when the setting is changed, follow the steps below. Settings

are saved in memory and are displayed anytime the unit is turned on by pushing the button.

 Preparation

• When the circuit breaker is turned on, the partition

lines are displayed on the remote controller.

* After the circuit breaker is turned on, the remote

controller does not accept any commands for

approx. 1 minute, this is not a failure.

REQUIREMENT

When the air conditioner is re-powered after it has not

been used for a long period, turn on the circuit breaker at

least 12 hours before starting the air conditioner.

◆ Start

1 Push button.

The operation lamp illuminates, and the operation

starts.

2 Select an operation mode with the “ ”

button.

One push of the button, and the display changes

in the order shown below.

3 Select fan speed with “ ” button.

One push of the button, and the display changes

in the order shown below.

• When fan is in “ AUTO”, fan speed is

adjusted based on difference between set point

and room temperature.

• In heating operation, if the room temperature is

not heated sufficiently with speed “ LOW”

operation, select “ MED.” or “ HIGH”

operation.

• The temperature sensor detects the return air

temperature at the indoor unit, which differs

from the room temperature depending on the

installation condition.

Set point is a target of room temperature.

( “Auto” is not selectable in the Fan mode.)

4 Select the set point temperature by pushing

the “TEMP. ” or “TEMP. ” buttons.

◆ Stop

1 Push button.

The operation lamp goes off, and the operation

stops.

In the COOL, DRY, or AUTO (cooling) mode, the

fan runs for 10 minutes (or more) for dehydrating

heat exchanger operation.

NOTE

Auto Changeover

• During Auto Mode, the unit selects the operating

mode (cooling, heating or fan only) based on the user

set point temperature.

• If the Auto mode is uncomfortable, the desired

conditions can be selected manually.

Cooling

If there is a demand for cooling, unit will start

approximately 1 minute after mode is selected.

Heating

• If there is a demand for heating, unit will start

approximately 3 to 5 minutes after the mode is

selected.

• After the heating operation has stopped, fan may

continue to run for approx. 30 seconds.

• When the room temperature reaches the set

temperature, the outdoor unit stops and the indoor unit

fan runs at extremely low speed.

During defrost operation, the fan stops so that cool air is

not discharged. (“ ” Pre-heat is displayed.)

When operation is restarted after stop

When the unit is restarted immediately after it was

stopped, the unit can not start for approx. 3 minutes this

is to protect the compressor.

SET

TIME

TIMER SET

TEST

FILTER

RESET

TEMP.

FAN

SAVE

SWING/FIX

VENT

MODE

ON / OFF

UNIT LOUVER

Auto Heat Dry FanCool

Auto High Med. Low

25-EN 26-EN

+001111055901_01EN.book Page 13 Saturday, October 8, 2011 10:44 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toshiba RAV-SM806KRT-E Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info