Bedienungsanleitung Toshiba TDP-D2 (Seite 14 von 20) (Englisch)

485671

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Operations

You can call up on-screen menus, and conduct a number of adjustments and settings,

using the operation buttons

p.14

on the control panel (main unit side) and remote control.

■ How to use the menus

The menu shown below is only for operation instructions and might be different from

the actual display.

Using the menus

Note

• Menu adjustments and settings are saved when the power is turned off via the ON/

STANDBY button. If the main power switch is turned off before this, or the power goes

out, then the data will not be saved.

Display the Setting display menu

To Status display

The menu disappears

1. Start

2. Select a Category

3. Adjustments & Settings

4. Back

6. End

5. To Finish

Finish via the Status

display menu.

Select a category by using

There are following three

categorys.

Displays the current

adjustments of selected

category.

Item shown with gray

cannot be adjusted for the

current input source.

p.28

Image adjustment menu

p.28

Default setting menu

p.26

Display setting menu

p.29

The figure shows a typical example.

As the display may differ depending

on the item, use the following pages

as a reference.

Item

Adjustment/Setting Value

This mark signfy that

there are options.

Press to display a

list of options.

These marks signify the

items can be adjusted/set

by using .

These marks signify an

item can be switched by

using .

These marks signify the items can be selected from

the list by using .

After an item selected, apply it by pressing .

Press to open the menu

of the selected category.

■ Displaying Information [Status display]

This displays information about the input signal, lamp use time, etc.

Press the button twice (or press the CALL button on the remote

control once).

When the button is pressed once, the Setting

display menu appears. Pressing it again displays

information

p.27

. The table below shows what kind

of information is displayed. Press the button (or the

CALL button on the remote control) again to

dismiss the display.

“Ye s”: displayed, “No”: not displayed

Item Description

Computer Y/PB/PR Video S-video

Input Input source name Yes Yes Yes Yes

RGB signal mode RGB input mode

[Note 1]

Ye s N o N o N o

H-resolution Horizontal resolution (in bits) Yes No No No

V-resolution Vertical resolution (in bits) Yes No No No

H-frequency Horizontal sync frequency Yes No No No

V-frequency Vertical sync frequency

[Note 2]

Ye s N o N o N o

Sync Sync signal polarity

[Note 3]

Ye s N o N o N o

Signal format Y/PB/PR signal format No Yes No No

Video mode Color method of video signal No No Yes Yes

Lamp time Time of lamp use

[Note 4]

YesYesYesYes

Version Firmware version

[Note 5]

YesYesYesYes

Notes

1: The mode of supported RGB signals

p.36

is shown.

2: Same as the refresh rate of the computer signal.

3: Sync signal polarity shown as P (positive) or N (negative) for [H/V].

4: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be

used as a counter of guaranteed lamp time.) When the time displayed approaches 1,500

hours, consult with a store about getting a replacement lamp (for TDP-D1: TDPLD1 and for

TDP-D2: TDPLD2) (sold separately) prepared.

5: [Version] shows the version of the projector’s internal control program. This version is

referred to for customer service, etc.

Notes

• The displayed information will not be refreshed if the status changes. To refresh the

information, dismiss the display, then display it again.

• Conducting another operation while information is being displayed dismisses the

display.

Using handy features (Continued)

AUTO

KEYSTONE

AUTO

SET

PAG E

DOWN

FREEZE

MUTE

CALL

ON/STANDBY

LASER

ON/STANDBY INPUT

ON LAMP TEMP FAN

AUTO KEYSTONE AUTO SET

VOL.

Control panel

Remote

Control

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toshiba TDP-D2 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info