Bedienungsanleitung Toshiba tdp mt100 home cinema (Seite 16 von 43) (Englisch)

214664

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

Shutting down the projector

The projector automatically displays a black screen after no active source is

detected for 30 minutes. This black screen helps preserve the life of the pro-

jector. The image returns when an active source is detected or a remote or

keypad button is pressed.

Screen Save

You can make the black screen appear after a preset number of minutes by

turning on the Screen Save feature in the Settings>System menu. See

page 32.

Power Save

The projector also has a Power Save feature that automatically turns the

lamp off after no active sources are detected and no user interaction with

the projector is performed for 20 minutes. By default, this feature is off. See

page 32.

Turning off the projector

You can turn the projector off simply by toggling the power switch to the off

position.

You can also press the remote’s Power button to place the projector in the

Off state while it is running. When the Power button is pressed twice (once

to start the power-down process and a second time to verify that you want

to power the projector off), the lamp turns off and the LED blinks green for

one (1) minute while the fans continue to run to cool the lamp. While the

LED is blinking green, the projector does not accept any keypad and remote

control input.

When the lamp has cooled, the LED lights solid green and the fans slow

down to minimal speed. To turn off the projector, toggle the power switch to

the off position.

NOTE: Once the projector has been toggled off, you must wait for one (1)

minute before turning the projector on again. This allows the lamp to prop-

erly cool. However, if the remote was used to power the projector to the Off

state you do not need to wait one minute to turn it on again.

Troubleshooting your setup

If your image appears correctly on the screen, skip to the next section. If it

does not, troubleshoot the setup.

The LED on top of the projector indicates the state of the projector and can

help you troubleshoot.

The following tables show common problems. In some cases, more than one

possible solution is provided. Try the solutions in the order they are pre-

sented. When the problem is solved, you can skip the additional solutions.

Table 1: LED behavior and meaning

LED color/behavior Meaning

solid green The power switch has been toggled on

and the software has initialized. The pro-

jector has been powered off via the

remote.

blinking green The power switch has been toggled on

and the software is initializing, or the pro-

jector is powering down and the fans are

running to cool the lamp.

blinking red

see page 40 for more information

A fan or lamp failure has occurred. Make

sure the vents aren’t blocked (see

page 22).Turn off the projector and wait

one minute, then turn the projector on

again. If the projector has been working

for 3,000 hours or more (page 35),

replace the lamp and reset the lamp timer.

Contact your Toshiba dealer if the prob-

lem persists

solid red An unidentifiable error: please contact

your Toshiba dealer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toshiba tdp mt100 home cinema Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info