Bedienungsanleitung Toshiba tdp sc25 (Seite 17 von 25) (Englisch)

214538

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

Operations

Using the menu (Continued)

■ Displaying Information (Status display)

This displays information about the input signal, lamp use time, etc.

“Yes”: displayed, “No”: not displayed

Item Description

Computer Y/PB/PR

Video

Camera

S-video

Input Input source name Yes Yes Yes Yes

Mode name RGB input mode

[Note 1]

Yes No No No

H-resolution Horizontal resolution (in dots) Yes No No No

V-resolution Vertical resolution (in dots) Yes No No No

H-frequency Horizontal sync frequency Yes No No No

V-frequency Vertical sync frequency

[Note 2]

Ye s N o N o N o

Sync Sync signal polarity

[Note 3]

Ye s N o N o N o

Signal format Y/PB/PR signal format No Yes No No

Video mode Color method of video signal No No Yes No

Lamp time Time of lamp use

[Note 4]

Ye s Ye s Yes Ye s

Lamp reset count The count for lamp replacement Yes Yes Yes Yes

Total time

The total time that this projector is used

Yes Ye s Yes Yes

Version Firmware version

[Note 5]

Yes Ye s Yes Yes

Notes

1: The mode of supported RGB signals

p.45

is shown.

2: Same as the refresh rate of the computer signal.

3: Sync signal polarity shown as P (positive) or N (negative) for [H/V].

4: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as

a counter of guaranteed lamp time.) When the displayed time approaches 3,000 hours, consult

with a store about getting a TLPLV5 replacement lamp (sold separately) prepared.

5: [Version] shows the version of the projector’s internal control program. This version is referred

to for customer service, etc.

Note

• The displayed information will not be refreshed if the status changes. To refresh the

information, dismiss the display, then display it again.

■ The default setting menu

This menu shows placement status and other settings.

Sets projection mode in accordance with Placement Style.

Set the timer to wait for the power to be turned off after signal input stops.

Press . Switch with and .

Off (not turned off)/1 min./5 min./10 min./30 min./60 min.

Set whether the input with signals is only selected or not.

Sets whether to turn on the power when the ON/STANDBY button is pressed

(Manual), or when the power cord is plugged in (Auto). Manual Auto

Sets the lamp power.

Sets the cooling fan speed.

Press .

Resets all adjustments and settings to their factory settings.

Description

Item

Projection

mode

No signal

power off

Auto input

Power on

Lamp power

[Note 1]

Fan mode

[Note 2]

Reset all

(Rear mounted

from ceiling)

(Standard)

(Rear)

(Mounted

from ceiling)

On Off

Standard High

Yes No

Low Standard

p.20

Notes

1: When Lamp power is set to Low, the screen becomes a little darker, but the cooling fan noise gets

quieter.

2: Setting [Fan mode] to [High] increases the cooling fan speed. Set this option to use the projector,

for example, at high altitude (over 1,500 meters above sea level).

Notes

•

Note that in the event of a power outage but the power is restored afterwards, the projector

power will come on if Power on is set to Auto.

• When you turn off the projector even if Power on is set to Auto, you must press the ON/

STANDBY button to turn the power off.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toshiba tdp sc25 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info