Bedienungsanleitung Toshiba TDP-T30 (Seite 18 von 23) (Englisch)

485558

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

34 35

Maintenance

■ Displaying Information (Status display)

This displays information about the input signal, lamp use time, etc.

“Yes”: displayed, “No”: not displayed

Item Description

Computer Y/PB/PR Video S-video

Input Input source name Yes Yes Yes Yes

Mode name RGB input mode

[Note 1]

Ye s No N oNo

H-resolution Horizontal resolution (in dots) Yes No No No

V-resolution Vertical resolution (in dots) Yes No No No

H-frequency Horizontal sync frequency Yes No No No

V-frequency Vertical sync frequency

[Note 2]

Ye s No N oNo

Sync Sync signal polarity

[Note 3]

Ye s No N oNo

Signal format Y/PB/PR signal format No Yes No No

Video mode Color method of video signal No No Yes No

Lamp time Time of lamp use

[Note 4]

Ye s Ye s Yes Ye s

Lamp reset count The count for lamp replacement Yes Yes Yes Yes

Total time

The total time that this projector is used

Ye s Ye s Yes Ye s

Version Firmware version

[Note 5]

Ye s Ye s Yes Ye s

Notes

1: The mode of supported RGB signals

p.41

is shown.

2: Same as the refresh rate of the computer signal.

3: Sync signal polarity shown as P (positive) or N (negative) for [H/V].

4: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as

a counter of guaranteed lamp time.) When the displayed time approaches 3,000 hours, consult

with a store about getting a TLPLV5 replacement lamp (sold separately) prepared.

5: [Version] shows the version of the projector’s internal control program. This version is referred

to for customer service, etc.

Note

• The displayed information will not be refreshed if the status changes. To refresh the

information, dismiss the display, then display it again.

Using the menu (Continued)

About lamp

Maintenance

The product’s light source is a mercury lamp that lights at increased internal pressure. Be sure

to fully understand the following characteristics of the lamp and handle it with extreme care.

• The lamp may burst with a loud noise due to impact or deterioration, or fail to light at

the expiration of its life.

•How long it takes before the lamp bursts or the life expires may vary greatly by lamp.

Some may burst shortly after first use.

• Burst is likely to happen if the lamp is used after the replacement period has elapsed.

• When the lamp bursts, the broken pieces of glass may get inside the product or be

released outside from the openings for ventilation.

• When the lamp bursts, a slight amount of mercury gas enclosed in the lamp along with

glass dust may be released from the openings for ventilation.

■

Immediately replace the lamp when a sign appears on the screen.

• When the replacement time approaches, a message will appear on the screen.

• The risk of burst will increase if the lamp is continuously used without being replaced.

•Frequently check the used hours and prepare spares when the replacement time

approaches. (Refer to “Status display”.

p.34

)

■

When the lamp is broken

• If glass components, including a lamp and a lens, should break, handle the broken

pieces with care to avoid injury and contact your dealer for repair service.

• In the event of lamp burst, unplug the product from the wall outlet, leave and completely

ventilate the room. Then, thoroughly clean the area around the projector and discard

any edible items placed in that area.

• When the lamp bursts, consult a doctor if glass dust or mercury gas gets into your eyes

or you breathe it.

Lamp replacement

A lamp is consumable supplies. If used for extended periods, images will appear dark, and

the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The lifetime

of the lamp depends on condition of use.) If this happens, replace it with a new one

WARNING

• If the projector is mounted on the ceiling, it is recommended to use your Toshiba

dealership when the lamp has to be exchanged.

• When replacing, always use lamp “TLPLV5” (sold separately).

CAUTION

•

If you have been using the projector, the lamp will be very hot, and may cause burn injuries

Wait for the lamp to cool (for longer than 1 hour) before replacing it.

•

If the lamp should break, please handle with care to avoid injury due to broken pieces and

contact your dealer for repair service.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toshiba TDP-T30 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info