Bedienungsanleitung Toshiba TDP-T355 (Seite 23 von 31) (Englisch)

485560

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

Operations

[Off]: Displays the Input select menu.

Toggle with

buttons and press

button. (The input without signals

can be selected.)

[Power on]

Note that if [Power on] is set to [Auto], then if the main power switch is ON when

power is restored after a power outage, the projector will come on.

[Lamp power]

When [Lamp power] is set to [Low], the screen becomes a little darker, but the

cooling fan noise gets quieter.

Notes

• The lamp power selection that you made will not be switched in about 1 minute

after the power is on.

•For lamp protection, even it has been set to [Low], the lamp power mode stays in

[Standard] in about 1 minute after the power is on, and then it will be switched to

your desired selection mode.

[Fan mode]

Setting [Fan mode] to [High] increases the cooling fan speed. Set this option to

use the projector, for example, at high altitude (over 1,500 meters above sea level).

[Remote control]

Sets a remote control code from 4 types. You can set each code respectively for up

to 4 projectors. The factory setting is [1].

To switch codes, set the same code for the projector and the remote control.

A remote control code is applied after the setting is done.

•You cannot operate the remote control if the codes of the projector and the

remote control do not match.

Remote control code setting for remote control

Remove the battery cover and set the same remote control code switch as the

projector.

p.16

(Use a screwdriver with thin tip to set.)

[Key lock]

Protect from operating errors by locking on the control panel buttons of the

projector. (The remote control operations are available.)

Control panel operations are locked after the setting is done.

•To release the key lock, press the control panel’s RETURN button for 10 seconds.

The key lock is released with a beep sound.

Using the menus (Continued)

■ The default setting menu

This menu shows placement status and other settings.

DescriptionItem

Sets projection mode in accordance with Placement Style.

When projecting on a non-screen surface, select a color in

accordance with the projecting surface.

Press and switch with and .

Off/Green/Black/Brown/Blue/Beige

Set the time to wait for the power to be turned off after the last

operation is made with no input signal.

Press and switch with and .

Off (not turned off)/1 min./5 min./10 min./30 min./60 min.

Set whether the input with signals is only selected or not.

Sets whether to turn on the power when the ON/STANDBY button is pressed

(Manual), or when the main power switch is turned on (Auto).

Manual Auto

Sets the lamp power.

Sets the cooling fan speed.

When two or more projectors are used and controlled by the remote

control respectively, this menu sets the code for the projector and the

remote control.

[ or : Enter setting mode] [ : Select item] [ :

Select from 1, 2, 3, 4] [ :Confirm] [ :Select OK to end]

Press [Cancel] to return.

Lock the control panel buttons.

[ or : Enter setting mode] [ : Select item] [ :

Select On/Off] [ :Confirm] [ :Select OK to end]

Press [Cancel] to return.

Press . (The password and user logo are not reset.)

Resets all adjustments and settings to their factory settings.

Password function

When [Password] is [On], the Password Setting screen is displayed.

Projection

mode

Blackboard

mode

No signal

power off

Auto input

Power on

Lamp power

Fan mode

Remote control

Key lock

Reset all

Password

p.22

p.36

(Rear

ceiling)

(Standard)

(Rear) (Ceiling)

On Off

Standard High

Yes No

Off On

Low Standard

Detailed description

[Blackboard mode]

Projects the image in colors more like projecting on a screen.

Note

• The projected image may differ depending on

the type, color, and material of the blackboard

and wall even if the selected color is the same

as the projected screen.

[Auto input search]

[On]: Automatically searches the signals that can

be projected, and switches input from the

connected device that outputs the signals

each time the INPUT button is pressed. The

input from the connected device that outputs

no signals is skipped.

Computer (1) (Digital)

Y/P

(1) (Digital)

Computer (1) (Analog)

Y/P

(1) (Analog)

Computer (2)

Y/P

(2)

Computer (3)

Y/P

(3)

Video

S-video

Input select

/ shows whether signal is

input or not.

Input select menu

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toshiba TDP-T355 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info