214680
61
Zoom out
Zoom in
Vorherige Seite
1/78
Nächste Seite
61
Maintenance
CONTENTS
If there is some problem inside the projector,
the indicators light up or blink.
Trouble indications
Indicators
Or
(Lit in red)
(Off)
ON
LAMP
TEMP
FAN
(Lit in red)
(Lit in red)
ON
LAMP
TEMP
FAN
(Flashing
in orange)
ON
LAMP
TEMP
FAN
(Lit in red)
ON
LAMP
TEMP
FAN
(Lit in red)
Or
(Lit or flashing
in red)
(Lit or flashing
in orange)
Or
Or
Or
(Lit in red)
(Lit in red)
(Lit in green)
(Lit in green)
(Lit in orange)
O
N
LAMP
TEMP
FAN
(off)
The power does not come on.
Malfunction of the unit.
Unplug the power cord and call the dealer.
The lamp turns off or does not light up.
The projector will return to the standby mode in about 2 minutes.
If the projector does not operate normally when the power is switched on again,
the lamp is at the end of its life duration or the unit has a fault.
Lamp's life duration is over, replace the lamp with a new one.
Unplug the power cord and call the dealer.
The power turns off or does not come on.
The inside is too hot, or the projector has been working in an area of high
temperature.
Place the projector correctly so the intake and exhaust fan's holes are not covered.
Turn the projector off, and leave it for a while, and turn it on again.
Clean the air filter.
* The icon appears before the power turned off.
* The projector returns to the standby mode after the fault display has been shown
for about 2 minutes.
The power turns off or does not come on.
Trouble with the cooling fan.
Unplug the power cord and call the dealer.
* The icon appears before the power turned off.
* The projector returns to the standby mode after the fault display has been shown
for about 2 minutes.
The power turns off or does not come on.
The lamp cover is not properly attached.
Unplug the power cord and reattach the lamp cover.
* The icon appears before the power turned off.
* The projector returns to the standby mode after the fault display has been shown
for about 2 minutes.
65
62
66
K
E
Y
S
T
O
N
E
A
U
T
O
S
E
T
E
X
I
T
ON / STANDBY
VOL / ADJ
E
N
T
E
R
M
E
N
U
I
N
P
U
T
F
A
N
T
E
M
P
L
A
M
P
O
N
Control panel
(Main unit side)
Notes
If abnormality occurs while operating, unplug the power cord.
When reinserting the power cord before the lamp has cooled, please wait until the lamp has
cooled sufficiently before use. When the lamp is at a high temperature, it may not light and the
life duration will be shortened.
61

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Toshiba tlp 261 with document camera wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info