Bedienungsanleitung Toshiba tlp 550 lcd projector (Seite 66 von 77) (Englisch)

214681

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

Others

CONTENTS

Before calling service personal

Symptom

The power does not come on.

The power turns off while

using the projector.

No image appears.

No sound is heard.

Desired input source cannot

be selected by the INPUT

button.

Analog RGB input or Y/P

B/PR

input colors are not right.

The image is blurred.

Focusing is uneven.

The picture is dim.

The color is faint.

The tint is not good.

Cause

• The power cord is disconnected.

• The lamp cover is not attached correctly.

• The ambient temperature of the projection room is too high.

• The lens cover is on.

• The wrong input is selected.

• The muting mode is on.

• The “Brightness” adjustment is at its darkest.

• The source is not correctly connected to the projector.

• The wrong input is selected.

• The muting mode is on.

• The sound volume is at it’s minimum.

• The source is not correctly connected to the projector.

•

Input is not set so that it can be selected with the INPUT button. By

default, only the Analog RGB and Video input modes can be selected.

• The COMPUTER connector's input setting is wrong.

• The lens is dirty.

• The picture is out of focus.

• The projection distance is not appropriate.

• The projecting light is not hitting the screen squarely.

• The “Brightness”, “Contrast”, “Sharpness” or “Phase” adjustments

are not correct.

• The “Brightness” or “Contrast” adjustments are not correct.

• The lamp life is ending.

• The “Color”, “Tint”, “R-Level”, “G-Level” or “B-Level” adjustments

are not correct.

• The lamp life is ending.

Correction

Firmly plug in the power cord.

Attach the cover correctly.

Lower the ambient temperature of the projection room,

and turn the power on.

Take off the lens cover.

Select the input source correctly.

Press MUTE to restore the picture.

Make the “Brightness” adjustment.

Connect the source correctly to the projector.

Select the input source correctly.

Press MUTE to restore the sound.

Adjust the sound volume.

Connect the source correctly to the projector.

Set from the menu screen so that the source can be

selected with the INPUT button.

On the menu screen, set for the proper input signal type.

Clean the lens with a blower or lens cleaner, etc.

Focus the picture.

Adjust the distance properly.

Adjust the projecting direction so that the light hits the

screen squarely.

Make the “Picture” adjustments.

Replace the lamp.

Make the “Color” adjustments.

Replace the lamp.

Page

Check the following points before asking for support service. Refer also to “Trouble indications”.

Continued

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toshiba tlp 550 lcd projector Seite 66

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info