Bedienungsanleitung Toshiba TLP-S10 (Seite 12 von 22) (Englisch)

485563

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

Operations

Projector placement angle adjustments

The placement angle and the height of the projected image can be adjusted by the foot

adjuster.

q Lift up the front of the projector to

the desired angle, then press the

foot adjuster release button.

The foot adjuster extends. Release the

button to lock the position.

w Turn the foot adjuster to fine-tune

the angle.

e To adjust the horizontal angle, use

the tilt adjuster.

To stow the foot adjuster, hold up the projector while pressing the foot adjuster

release button, then slowly lower the projector.

Adjust the picture size and focus.

q Move the projector back and forth to adjust

the screen size.

w Use the focusing ring to adjust the focus.

Adjusting the volume with the buttons

The speaker volume can be adjusted when an audio signal is being input.

Notes

•

Note that because of the lamp characteristics, the brightness of the lamp may fluctuate slightly

• A lamp is a consumable supply.

If used for extended periods, images will appear dark, and the lamp could burn out. This

is characteristic of a lamp, and is not malfunction. (The lifetime of the lamp depends on

conditions of use.)

• The LCD panel is made using extremely advanced technology, but there may be black

spots (pixels that do not light) or bright spots (pixels that are constantly lit) on the panel.

Please note that these are not malfunctions.

•

Although this projector supports a wide range of RGB signals

p.38

, any resolutions not

supported by the model (XGA or SVGA, depending on the model) will expand or shrink the

pictures, and will affect image quality slightly. To view high-quality images, it is

recommended that the computer’s external output should be set to the projector’s resolution.

• With some models of computer having LCD displays or the like, displaying images

simultaneously on the projector and the monitor’s display may cause the images to be

shown improperly. If this happens, turn off the computer’s LCD display. For information on

how to turn off the LCD display, see the owner’s manual of your computer.

• If a signal not supported by the projector is input, the

icon will appear.

• If a no signal is being input from the connected device, the

icon will appear.

• If an unavailable operation button is pressed, the

icon will appear.

Turn on the power.

Turn on the power by following the instructions in “Turning on the power”

p.20

Select the language and the lamp power (When using the

first time).

When the projector is used for the first time after purchase, menu for language and

lamp power selection and configuration is displayed in English. (If the screen is out of

focus, adjust it according to the step

q Use the or buttons to select the

desired language and press the

button.

Message for setup confirmation is displayed in a

selected language.

w Using the or button, select Standard

or Low and press the

button.

The lamp power, if selected, will be toggled without

pressing the

button. The display automatically

disappears in a few seconds.

Notes

• When the projector is turned on the next time, the Language and Lamp power

menus do not appear upon startup. However, if “Reset all” is executed from the

Reset menu

p.31

, the Language and Lamp power menus will be displayed the next

time when the power is turned on

• The language can also be set via the Display setting menu

p.30

and Lamp power

via the Default setting menu

p.30

• This owner’s manual assumes that English has been selected.

Place connected device(s) in operating status.

Turn on and boot up connected computers and other devices.

Select input.

q Press the INPUT button.

A list of inputs appears on the screen.

w Use the buttons to select the desired

input, and press the

button.

The picture for the selected input is projected.

Basic operations

English

Français

Português

Deutsch

Italiano

Español

................

..............

................

...............

..........

...................

.......

...................

English

French

German

Italian

Spanish

Portuguese

Japanese

Chinese (simplified)

Chinese (traditional)

Korean

Computer

Y/P

Video

S-video

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toshiba TLP-S10 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info