Bedienungsanleitung Toshiba tlp x100 (Seite 24 von 29) (Englisch)

215803

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

46 47

Maintenance

Air ﬁlter cleaning

The air ﬁlter prevents dust and debris from getting inside the projector. Never run the pro-

jector with the ﬁlter removed. It is recommended that the air ﬁlter is cleaned regularly.

• The message “Check the air ﬁlter for dirt.” is displayed every 100 hours. (If the usage time

exceeds 100 hours, this message is displayed for about 30 seconds when the image is

displayed for the ﬁrst time after power is turned on. This display will be dismissed with any

operation.)

• Check out the ﬁlter and any debris is found, use the following procedure for cleaning.

WARNING

• Request cleaning and maintenance of a ceiling-mounted unit from your projec-

tor dealership.

Unplug power cord.

Remove the air ﬁlter.

Pull out the air ﬁlter by holding the release knob

with your ﬁngers as shown in the ﬁgure.

Clean the ﬁlter.

Carefully remove the dust and dirt from the air ﬁlter

with a vacuum cleaner or the like.

Replace the air ﬁlter.

Insert the air ﬁlter ﬁrmly until you hear a click.

Notes

• Allowing dirt and dust to build up in the air ﬁlter will worsen the air circulation inside the

projector, causing the internal temperature to rise, causing the projector to stop working

or malfunction.

• Insert the air ﬁlter all the way in. Leaving gaps will allow dust and dirt to get inside the

projector again.

• If you wash the air ﬁler with water, make sure to dry it completely before replacing it.

• If the air ﬁlter is torn, consult with your dealer about replacing it with a new one.

Continuing to use a ripped ﬁlter will allow dust and dirt to get inside the projector.

Notes and Precautions

The [Lamp time] item in the Status display menu indicates the time of lamp use (as a

rough guide)

p.42

Please replace the lamp after 2000 hours of use with [Lamp power] in the Default

setting 1 menu set to [Standard], and 3000 hours of use with [Lamp power] in the

Default setting 1 menu set to [Low].

p.40

There are cases that the lamp can not work before the above mentioned period expires

or before the replacement message is displayed.

Attach the outer lamp cover correctly so that it is not loose. If it is not attached correctly,

the projector may fail to be powered on or the lamp may fail to come on.

Always replace the lamp with a new one.

The lamp is made out of glass. Do not touch the glass surface with your bare hands,

bang it, or scratch it. (Dirt, jolts, scratches and the like could break the lamp.)

About lamp replacement messages

The lamp replacement message of this projector displays an appropriate

period according to the use period for [Standard] / [Low] of the [Lamp power]

respectively.

When the replacement time approaches, the message of “The lamp life is ending.

Please change the lamp.” is displayed every time the power is turned on. This

display disappears when you press the button.

•

Used Lamps

This projector’s lamps contain trace amounts of environmentally harmful inorganic

mercury. Be careful not to break used lamps, and dispose of them in accordance with

local regulations.

•

Lamp replacement (Continued)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toshiba tlp x100 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Toshiba tlp x100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info