Bedienungsanleitung Toshiba tlp x3000 (Seite 23 von 31) (Englisch)

214601

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

Operations

Using the menus (Continued)

[Key lock]

Protect from operating errors by locking on the control panel buttons of the

projector. (The remote control operations are available.)

Control panel operations are locked after the setting is done, and accordingly

operation with the control panel buttons is disabled.

•To release the key lock, set the [Key Lock] to [Off] using remote control. Pressing

the [RETURN] button on the projector for 10 seconds also sets the [Key Lock] to

[Off]. (When operating the main unit, the 2 indicators of LAMP and TEMP light in

orange for 3 seconds, and at the same time the projector beeps.)

■ Displaying Information (Status display)

This displays information about the input signal, lamp use time, etc.

“Yes”: displayed, “No”: not displayed

Camera

Item Description

Computer Y/PB/PR Video S-video

(XC2500A/

XC3000A)

Projector

Input Input source name Yes Yes Yes Yes Yes

Mode name RGB input mode

[Note 1]

Ye s N o N oNo No

Resolution Resolution (in dots) Yes No No No No

Frequency Sync frequency Yes No No No No

Sync Sync signal polarity

[Note 2]

Ye s N o N oNo No

Signal format Y/P

signal format No Yes No No No

Video mode Color method of video signal No No Yes Yes No

Lamp time Time of lamp use

[Note 3]

Ye s Ye s Ye s Ye s Ye s

Lamp reset count The count for lamp replacement Yes Yes Yes Yes Yes

Total time The total time that this projector

is used.

Ye s Ye s Ye s Ye s Ye s

Version Firmware version

[Note 4]

Ye s Ye s Ye s Ye s Ye s

Notes

1: The mode of supported RGB signals

p.57

is shown.

2: Sync signal polarity shown as P (positive) or N (negative) for [H/V].

3: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as

a counter of guaranteed lamp time.) Please replace the lamp after 2000 hours of use if [Lamp

power] is set to [Standard], or after 3000 hours of use if [Lamp power] is set to [Low], consult

with a dealer about getting replacement for lamp TLPLW11 (sold separately).

4: [Version] shows the version of the projector’s internal control program. This version is referred

to for customer service, etc.

Note

• The displayed information will not be refreshed if the status changes. To refresh the

information, dismiss the display, then display it again.

Please read this chapter if the model you purchased includes a document camera.

■ Preparation of the document camera

1) Setup the arm

Status before preparation

(When stored)

3) Let the camera lens face below

2) Raise the camera head

4) Let the camera lens face the object

PRECAUTIONS

• Do not jolt or force the camera head or camera arm. Doing so could cause malfunction.

• The CMOS image sensor mounted on the camera of this projector is produced by

precision engineering. Please be informed that missing pixels and bright spots are not

considered as problems.

Note

• It takes about 10 seconds from when the power is turned on until the operation is

possible. This is not a problem.

Using the document camera

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toshiba tlp x3000 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info