Bedienungsanleitung Toshiba tlp xd3000 (Seite 13 von 28) (Englisch)

215855

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Operations

Turn on the power.

Tu rn on the power by following the instructions in “Turning the power on”

p.23

Select the language (When using the first time).

When the projector is used for the first time after purchase, the start menu for lan-

guage (to display the menus and messages on the screen) selection is displayed in

English. (If the screen is out of focus, adjust it according to the step

Use the or button to select the desired

language and press the

button.

Message for setup confirmation is displayed in a

selected language.

Notes

• When the projector is turned on the next time, the start menu does not appear upon

startup. However, if [Reset all] is executed from the Default setting 2 menu

p.41

the start menu will be displayed the next time when the power is turned on.

• The language can also be set via the Display setting menu

p.37

• This owner’s manual assumes that English has been selected.

Activate the connected device.

Tu rn on and start the connected device such as a computer.

Press the INPUT button.

An image of the connected equipment is projected.

Each time you press the INPUT button, it switches to the input of the connected

equipment that is outputting video signals.

Notes

• When [Auto input search] is set to [Off] in the Default setting 1 menu

p.40

(factory

setting is [On]), the Input select menu appears if you press the INPUT button.

• If no signal is being output from the connected equipment, pressing the INPUT button

does not change the input and “There is no other input signal.” will appear.

Basic operations

English

French

German

Italian

Spanish

Portuguese

Russian

Swedish

Tu r kish

Polish

Japanese

Chinese (simplified)

Chinese (traditional)

Korean

Notes

• The start-up screen will disappear after a moment. You can dismiss the start-up screen

before this by performing any operation. You can also configure the system to prevent the

start-up screen from appearing. To do this, use the Display setting menu

p.37

• The first time you use the projector after purchase, after the start-up screen disappears,

the start menu is displayed

p.25

• Beep sound can be set not to beep in the Default setting 1 menu

p.40

• When [Key lock] is [On], the operation buttons of the projector do not work

p.41

• When [Password setting] is [On], then the start-up screen is displayed after the

Password entry screen disappears

p.31

■ Turning the power off

Press the ON/STANDBY button.

A message appears on the screen, confirming that you wish to shut off the power. This

message will disappear after a moment. (This operation is no longer valid after the

message disappears.)

Press the ON/STANDBY button once again.

When the setting of beep sound is [On], the projector beeps, and the screen turns off,

but the internal cooling fan continues to operate. Then, the projector goes into standby

mode.

During cooling, the ON/STANDBY indicator flashes. While the

indicator is flashing, the power can not be turned back on. At this

point of time, it does not matter even if you unplug the power

cord.

Note

• The projector consumes about 10W of power in standby. We recommend that you unplug

the power cord if you will not be using the projector for an extended period.

PRECAUTION

• If you turn the power on before cooling is complete, give the lamp time (about 5 minutes)

to cool before plugging it back in. If the lamp overheats, it may fail to light.

Turning the power on and off (Continued)

LCD Panels

LCD panels wear out. In order to prolong the lifetime of your LCD panel, take the

following precautions.

• In order to extend the lifetime of the LCD panel, always turn off the power when not in

use, and make sure that the lamp is off. Keeping the lamp off is also very effective at

saving electricity.

• If the air filter becomes dirty and clogged, the projector’s internal temperature will rise,

shortening the lifetime of the LCD panel and causing malfunctions. Clean the air filter

from time to time

p.46

, and replace it periodically. Contact the store where you

purchased your projector, or your local Service Station for replacement air filters.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toshiba tlp xd3000 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info