Bedienungsanleitung Tower T12024 (Seite 8 von 16) (Englisch)

671116

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

3USINGYOURAPPLIANCE

Assembly:

CAUTION: Do not plug the product into an

electrical outlet until it is fully assembled.

Before using the product for the rst time,

disassemble and wash as follows:

1. Unscrew the blade assembly from the cup

and carefully remove the gasket from its

groove.

CAUTION: Handle blades carefully, as they are

sharp.

2. Wash all parts except the base and power

cord in warm, soapy water or place them

in the top rack of an automatic dishwasher,

then rinse and dry thoroughly.

WARNING: Do not immerse the base or power

cord in water or other liquids.

NOTE: Do not use abrasive cleaners to clean

any part of the product.

3. Insert the gasket into the groove in the

blade assembly and securely retighten

the blade assembly onto the top of the

cup. Note that the lip of the gasket faces

upward.

NOTE: When inserting the gasket into the

groove, press the gasket rmly around all sides

and test it by turning the blade assembly upside

down to make sure the gasket is not loose or

does not fall out. There will be a small bump

underneath the gasket where the safety interlock

mechanism protrudes; this is normal.

4. Place the base on a at, level, stable

surface. To attach the cup assembly (with

the cup and the blade assembly securely

attached together), align the

symbol on

the bottom edge of the blade assembly with

the

mark on the base and turn clockwise

until it is rmly in place, aligned with the

symbol.

Usingyourappliance:

1. Ensure the power cord is unplugged from

the electrical outlet, then remove the cup

assembly from the base and unscrew the

blade assembly.

2. Pour any liquid ingredients into your

Personal Blender cup rst, to help lubricate

the blades. Cut all solid ingredients into

small pieces.

3. Ensure the gasket is securely seated in the

blade assembly, and then securely tighten

the blade assembly clockwise onto the top

of the cup.

4. To attach the cup to the Personal Blender

base, align the

symbol on the bottom

edge of the blade assembly with the

mark on the base and turn clockwise until it

is rmly in place, aligned with the

symbol.

NOTE: Product will not operate and ready light

will not illuminate unless both the cup and blade

assembly are attached properly to the base.

5. Plug in your Personal Blender. The power

indicating light will illuminate.

6. Press the power button to start blending.

NOTE: If the blades are not operating smoothly,

stop the product and add some liquid, or reduce

the solid contents in the cup.

7. Press the power button again to shut the

blender off.

8. When the blades have stopped, unplug

the power cord from the electrical outlet,

remove the cup from the base, and turn the

cup right-side up.

9. Unscrew the blade assembly from the cup

and empty the contents into a separate

container or screw a drinking lid onto your

cup to enjoy your smoothie on the go!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tower T12024 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info