Bedienungsanleitung Toyota Mirai 2022 (Seite 393 von 578) (Englisch)

795727

393

Zoom out

Zoom in

Vorherige Seite

1/578

Nächste Seite

391

Owners Manual_Europe_M62060_en

7-3. Do-it-yourself maintenance

Maintenance and care

for approximately 1 minute then illumi-

nate and “---” will be displayed for the

inflation pressure of each tire on the

multi-information display.

7Drive at 40 km/h (25mph) or

more for approximately 10 to 30

minutes.

Registration is complete when the tire

pressure warning light turns off and the

inflation pressure of each tire is dis-

played on the multi-information display

Even if the vehicle is not driven at

approximately 40 km/h (25mph) or

more, registration can be completed by

driving for a long time. However, if reg-

istration does not complete after driving

for 1 hour or more, perform the proce-

dure again from the beginning.

8Initialize the tire pressure warn-

ing system. (P.388)

■When registering ID codes

●ID code registration is performed

while driving at a vehicle speed of

approximately 40 km/h (25 mph) or

more.

●Before performing ID code registra-

tion, make sure that no wheels with

tire pressure warning valve and trans-

mitters installed are near the vehicle.

●Make sure to initialize the tire pres-

sure warning system after registering

the ID codes. If the system is initial-

ized before registering the ID codes,

the initialized values will be invalid.

●ID codes can be registered by your-

self, but depending on the driving con-

ditions and driving environment,

registration may take some time to

complete.

■Canceling ID code registration

●To cancel ID code registration after it

has been started, turn the power

switch off before driving the vehicle.

If the vehicle is driven after ID code

registration is started, to cancel regis-

tration, perform the ID code registra-

tion start procedure again and turn the

power switch off before driving.

●If ID code registration has been can-

celed, the tire pressure warning light

will blink for approximately 1 minute

when the power switch is turned to

ON and then illuminate. The tire pres-

sure warning system will be opera-

tional when the tire pressure warning

light turns off.

●If the warning light does not turn off

even after several minutes have

elapsed, ID code registration may not

have been canceled correctly. To can-

cel registration, perform the ID code

registration start procedure again and

then turn the power switch off before

driving.

■If ID codes are not registered prop-

erly

●In the following situations, ID code

registration may take longer than

usual to be completed or may not be

possible. Normally, registration com-

pletes within approximately 30 min-

utes.

• Vehicle is not parked for approxi-

mately 20 minutes or more before

driving

• Vehicle is not driven at approximately

40 km/h (25 mph) or more

• Vehicle is driven on unpaved roads

• Vehicle is driven near other vehicles

and system cannot recognize tire

pressure warning valves and transmit-

ters of your vehicle over those of other

vehicles

• Wheel with tire pressure warning

valve and transmitter installed is

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toyota Mirai 2022 Seite 393

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Toyota Mirai 2022

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info