Bedienungsanleitung Toyotomi EPA-150EF (Seite 3 von 25) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

728842

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

-3- -4-

ENGLISH ENGLISH

1. Function Introduction

(1) ON/OFF: Power on, inset the plug, the heater enters into standby mode. Press

and the heater start to work

under the previous mode, LED display show the set temperature. Power off, press

again, the heater stop to

work and enter into standby mode, display show

;

(2) Power setting: When user uses the heater for the ﬁ rst time, it works in default mode-high power. Press

, enter

into low power mode, the

indicator light will on; press , enter into high power mode, the indicator light

will off,

indicator light will on.

(3) Temperature setting: Under working mode, press

to increase or decrease the temperature degree. The

temperature range is 5°C-35°C. Press the key over 2s, the degree can set quickly. When ﬁ nish setting, it conﬁ rm

automatically, the dot stop ﬂ ashing and off, the LED display shows setting temperature. Note: If under Anti-frost

mode, the temperature cannot be setting.

(4) Timer off setting: When the heater is working, press

, the timer indicator light will ﬂ ash, the display shows timer,

press

to set the hours, range is 0-24 hours. Press the over 2s, can set the hour quickly. After 5s ﬁ nish

setting timer, the

indicator light on. Display shows the set temperature.

(5) Anti-frost mode: Under working mode, press

, the indicator light on. Press again, the anti-frost mode

cancelled and indicator light off.

(6) Child lock function: Press

together for 3s, the display shows [ ] symbol, after 5s, display shows the previous

status, the keys cannot work. If press the keys, display is ﬂ ashing [ ] symbol. Press

together for 3s again, the

keys unlock.

(7) Memory function: If suddenly power off, after power on again, the heater will enter into previous working mode.

Installation the panel heater

Recommended Installation The convector shall be installed so that produced heat will mix

maximum volume of air. The convector should be attached in accordance with applicable

requirements. The switch and other mechanisms should be away from a person who takes bath

or shower. The device should not be exposed to water splashes. If the device is covered there is

a risk of overheating. It is strictly forbidden to cover or plug inlets and outlets (air grids) as it can

cause an accident or damage the device. DO NOT place the convector behind curtains, doors,

under wall opening or ventilation hole. Keep minimum distance required for installation on ﬂ oor,

surface, near furniture, etc. (Figure 1).

Wall Mounting:

DO NOT ﬁ t the castors to the base of the heater. Make sure

the heater is unplugged from the mains power and the wall

is suitable for mounting the panel heater and there are the

correct clearances. Make sure the panel heater is within 1

meter of a power socket.

Detach the mounting bracket from the rear of the heater by compressing the

2 bracket clips, pulling the clips out of the heater rear & removing the bracket

hooks from the heater.

Figure 1

Position the bracket on the wall in the desired position & drill holes for two mounting screws. Once the holes are drilled,

use two screws (appropriate for the type of wall) to ﬁ x the bracket ﬁ rmly in place. Check for strength.

Carefully place the heater (slightly tilted forward) onto the hooks at the bottom of the bracket & rotate back so the clips

ﬁ x back into their original holes. Check that they are ﬁ xed correctly. If possible, have a second person help to check for

alignment as the heater is attached. The heater is now ready to connect to the mains power.

Floor Mounting:

The device can be mounted on special legs enabling to move it in the room.

Support foots are attached as follows:

Turn the convector upside down;

Take one of support foots with rollers;

Place the plate of the support foot to the attaching point on the convector so that the dome-shaped part of the plate will

be tightly attached to the convector close to its rear panel the screw holes should match;

Tighten the support foots with the screws in parts kitting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toyotomi EPA-150EF Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info