Bedienungsanleitung Toyotomi TD-C100 (Seite 5 von 8) (Deutsch, Englisch, Holländisch, Französisch)

728861

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

CAUTION

• Keep unit more than 20 cm away on the rear side (F2), 10cm

away on the upper and both side (F1), and 15 cm away on the

front side (F3) from any objects or wall. (Fig. F)

• Remove drain water before moving unit.

• To minimize corrosion, DO NOT use in damp, salty air area.

• DO NOT operate in direct sunlight.

• DO NOT use for such particular purpose as preservation of

foodstuff, animals, plants, precision appliances, arts and med-

icine.

• DO NOT place an animal, plants or combustion equipment in

a place which is subjected to the direct air flow of the unit.

• DO NOT ride or place the objects on the unit.

• DO NOT turn the product on its side or upside down.

• DO NOT remove the rubber cap cover of water drainage outlet

except in continuous drainage mode to avoid water leakage.

• Waste electrical products should not be disposed

with household waste.

• Please recycle where facilities exist. Check with

your local authority or retailer for recycling advice.

3. OPERATION

OPERATING STEPS:

1. CONNECT POWER PLUG (B4) TO POWER SOCKET.

Make sure the water tank (A5) is placed in proper position, and

then connect to the power socket.

If the tank is not in proper position, the FULL lamp (C3) will

light light after plug on. If FULL lamp lights at the first time,

please pull out the tank once and push it back to the proper

position.

2. PRESS POWER BUTTON (C1) TO ON.

3. PRESS HUMIDITY SETTING BUTTON (C4)

Press the humidity setting button (C4) to select your desired

humidity mode.

By pressing the humidity setting button, indication lamp will

shift to; “CONTINUE” (C5)

➞ “60%” (C8) ➞ “50%” (C7) ➞

“40%” (C6) ➞ CONTINUE” (C5) and your desired humidity

mode can be selected.

4. STOP OPERATION

Press the “POWER” button (C1) and all lights will go out.

For the internal drying operation, the unit will stop operation

after the 30 minutes of fan operation.

During the internal drying operation, the humidity setting lamp

of 40%, 50% and 60% will continue lightning one by one.

To stop the internal drying operation, press the Power button

more than 3 seconds during the internal drying operation.

4. EMPTY THE WATER TANK (Fig.D)

1. Stop the operation.

NOTE: When the water tank is full, the Full lamp (C3) will blink

and unit stops automatically in a few minutes.

2. Remove the water tank. (Fig D1)

NOTE: Do not move the unit or remove the water tank, if the

machine is still operating, as water may leak, damage

the unit or cause an electric shock.

Do not remove or damage the float in the water tank, or the

unit cannot work correctly.

3. Carry the water tank with handle. (Fig.D2)

4. Pour water away. (Fig. D3)

5. Restore the water tank to the correct position.

NOTE: If the water tank is not well in the position, the Full

lamp (C3) will blink.

5. CONTINUOUS DRAINAGE WATER (Fig. E)

1. Prepare a hose that is inner diameter of 13mm or 15mm, and

take out the outlet cap (E1).

2. Remove the rubber stopper (E2) inside the outlet cap (E1).

Then you can see the hole. (Fig. E5)

3. Put the hose (E4) into the drain water outlet (E3). (Fig. E6)

NOTE:

• In case of using the hose of inner diameter of 15mm, insert the

hose to the drain water outlet all the end. (E7)

• In case of using the hose of inner diameter of 13mm, put the

hose into the tip of drain water outlet (E8)

• During the continuous drainage mode, the drain hose must be

horizontally or below the drainage hole (E9), and try not to

raise the hose above the drainage hole (E10) or fold the hose

(E11).

6. CLEANING

CLEANING AIR INTAKE FILTER (Fig. G)

1. Clean the air intake once every two weeks.

2. To remove the air intake filter, pull the water tank out of the

unit and draw out the air filter. (Fig. G1)

3. Remove the dust with a vacuum cleaner (Fig. G2), or wash the

dust away with water. If you wash it with water, dry it in the

shade after washing it.

WARNING

• DO NOT touch the evaporator. It may cause injury or damage.

CAUTION

• DO NOT use over 40˚C hot water. The plastic part may be de-

formed.

• Disconnect the power supply before cleaning and mainte-

nance.

CLEANING SURFACE

Clean the outside of the product with a soft damp cloth.

CAUTION

• NEVER use gasoline, solvents, chemical, products or polish as

they could damage the surface.

7. LONG-TERM STORAGE

At the end of each season, or when you do not plan to use this

product for an extended period of time, the following procedures

are recommended.

1. Empty the water tank.

After stopping operation, leave it for one day and empty the

water tank.

2. Take off the outlet cap (E1) and rubber stopper (E2) which is

for continuous drainage.

When you take the rubber stopper (E2) off, the drain water will

come out. Therefore receive the water with a bucket or a tank.

3. Clean the unit, tank and filter.

Wipe off any dirt or dust on the unit with a soft damp cloth or

a vacuum cleaner, and then wipe again using a soft dry cloth.

4. Store the unit.

The original shipping carton is the best place to store your

unit. If you do not have the original packing materials, cover

the unit with a large plastic bag and store in a cool dry place.

CAUTION:

• ALWAYS store the unit at less humidity and airy place with

standing vertically.

• DO NOT put heavy objects on top of the unit.

8. TRANSPORTATION

Preferably keep the unit in the vertical position during transporta-

tion. If it is necessary to place the unit in a horizontal position more

than 1/2 hour, ALLOW IT TO REMAIN UPRIGHT FOR 24 HOURS

BEFORE OPERATION. Failure to do so may result in damage to

the compressor. Before transporting / moving the unit make sure

the drain tank is empty.

ENGLISH

TD-C100.qxd 14.10.9 13:01 ページ 2

Toyotomi TD-C100 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info