Bedienungsanleitung TP-LINK RE355 (Seite 37 von 39) (Englisch)

664742

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

Appendix

T1. How do I restore my extender’s configuration to its factory default settings?

There are two ways to reset the extender:

● Option One: With the extender powered on, use a pin to press and hold

the RESET button until all LEDs turn on momentarily, then release the

button.

● Option Two: Restore the default settings from “System Tools > Restore

& Backup” of the extender's Web-based Management page.

T2. What can I do if I forget my password?

● Restore the extender’s configuration to its factory default settings. If you

don’t know how to do that, please refer to previous T1;

● Use the default username and password: admin, admin;

● Try to reconfigure your extender by following the instructions of this guide.

T3. What can I do if I cannot access the web-based configuration page?

● Check to verify all the connections (either wireless or wired ones) are

proper. If yes, please proceed to the next step; otherwise, check the

connections again.

● Try to obtain an IP address and gateway; if succeed, open your web-

browser, enter the default domain http://tplinkrepeater.net in the address

field and get logged in. If you are unable to log in, please RESET the device,

and then use the default IP address to get into the web-based configuration

page, reconfigure the device.

● Feel free to contact our technical support, if the problem still persists.

T4. How can I know that my wireless signal has been repeated and boosted

by RE355?

An easy way is to compare the signal strength of your target wireless

network (symbolized by its SSID), with RE355 in operation vs. out of

operation. Before comparison, you’d better make sure your computer can

obtain an IP address from your target wireless network and thus access the

Internet, either via RE355 or without.

T5. Will the extender work if I connect the ETHERNET port of it to the router

via Ethernet cable?

Sorry, it won’t work. The extender is designed to connect wirelessly to the

router, while the ETHERNET port is designed to connect with a wired

device, like Internet TV, Gaming console, DVR and so on.

T6. Why does the wireless transmission rate speed down, while the wireless

signal is stronger after repeated by RE355?

In compliance with the wireless transmission protocol, all the extender

devices are set to work in half-duplex instead of full-duplex mode. In other

words, the extender has to process one-way communication between your

root Wireless router (or AP) and the terminal clients; so the transmission

time will be double-increased, while the speed will be decreased. TP-LINK

recommends that you connect to the extender when your home network

connection is poor, or when you want a larger wireless coverage to

eliminate “dead zones”.

Once the extender is reset, the current configuration settings

will be lost and you will need to reconfigure it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

TP-LINK RE355 Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von TP-LINK RE355

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info