Bedienungsanleitung TP-LINK TD-W8960N (Seite 2 von 2) (Englisch)

664720

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Q1. What can I do if the login page does not appear?

A1. Make sure the computer is connected to the modem router properly.

A2. If the computer is set to a static or xed IP address, change the computer’s settings to

obtain an IP address automatically from the modem router.

A3. Verify http://tplinkmodem.net or 192.168.1.1 is correctly entered in the web browser

and press Enter.

A4. Use another web browser and try again.

A5. Reboot your modem router and try again.

A6. Disable and enable the active network adapter.

Q2. What can I do if I cannot access the internet?

A1. Make sure the telephone and Ethernet cables are plugged in correctly.

A2. Try to log in to the web management page of the modem router using the default address at

http://tplinkmodem.net or 192.168.1.1. If you can, try the following answers. If you cannot,

change the computer’s settings to obtain an IP address automatically from the modem

router.

A3. Consult your ISP and make sure all the VPI/VCI, WAN Link Type, account username and

password are correct. If they are not, please replace them with the correct settings and try

again.

A4. Restore the modem router to its factory default settings and reconfigure the modem router by

following the instructions in this Quick Installation Guide.

A5. Please contact our Technical Support if the problem persists.

Q3. How do I restore the modem router to its factory default settings?

Q5. What can I do if the ADSL LED does not turn solid on?

A1. Check your cables and make sure they are all plugged in correctly, including the

telephone lines and power adapter.

A2. Manually change your DSL settings. Log into the modem router’s web management

page. Go to Advanced Setup > DSL, untick all the modulation options except G.Dmt

Enabled, ADSL2 Enabled and AnnexL Enabled and click Save/Apply.

A3. Restore your modem router to its factory default settings by referring to FAQ > Q3.

A4. Remove the ADSL splitter, directly connect the modem router to the phone jack and

then reconfigure the modem router by following the instructions in this Quick

Installation Guide.

A5. Contact your internet service provider to verify if the ADSL line is in good status.

A6. Please contact our Technical Support if the problem persists.

Q4. What can I do if I forget my password?

Web management page password:

Refer to FAQ > Q3 to reset the modem router, and then use admin (all lowercase) for

both username and password to log in.

Wireless network password:

A1. The default Wireless Password/PIN is printed on the product label of the modem router.

A2. If the default wireless password has been changed, log in to the modem router's web

management page and go to Wireless > Security to retrieve or reset your wireless

network password (also called WPA/WAPI passphrase).

A1. With the modem router powered on, press and

hold down the WPS/RESET button on the rear

panel of the modem router for more than 5

seconds until all LEDs turn on momentarily,

then release the button.

WPS/RESET Button

Press & Hold for more than 5 seconds

Wireless

Wired

2. Configuring the modem router via a web browser.

Enter http://tplinkmodem.net or 192.168.1.1 in the address bar of a web

browser. Use admin for both username and password, and then click

Note: If the login window does not appear, please refer to FAQ > Q1.

Ethernet cable

Please consult your ISP (Internet Service Provider) for the following

information before configuring the modem router.

VPI and VCI: _______ WAN Link Type: _______

Encapsulation Mode (optional): _____________

If your WAN Link Type is PPPoE/PPPoA, please get further information of

your account username and password.

A2. Log in to the web management page of the modem router, and go to Management >

Settings > Restore Default, click Restore Default Settings and wait until the reset

process is complete.

Note: All the internet settings in the figure below are used for demonstration only.

Verify or change the Wireless settings (wireless network settings) and click

Next to continue.

Check all the parameters and click Confirm to complete the configuration.

Note: You may personalize your wireless network name and key. Once done, you will have to

reconnect to your Wi-Fi network using the new wireless network name and key.

Click Next to start Quick Setup, and select the WAN Type. Here we use

ADSL WAN for demonstration. Then click Next.

Select your Country and ISP from the drop-down list. Complete the WAN

settings with the information provided by your ISP and click Next. Here we

use PPPoE for demonstration.

Quick Setup - WAN Configurations

Skip WAN

Choose WAN Type:

For ADSL(Telephone line/RJ11) Service

For Ethernet(RJ45) ServiceEthernet WAN

ADSL WAN

Enable IPv6 for this service

Quick Setup - WAN Configurations

Please SelectCountry:

ISP: Other

WAN Link Type:

PPPoE (PPP over Ethernet)

35VPI/VCI: 8 ([0~255] / [32~65535])

XXXXXXXX

PPP Username:

********

PPP Password:

Encapsulation Mode:

LLC/SNAP-BRIDGING

(optional)

1480

MTU (bytes):

(optional)

PPPoE Service Name:

(optional)

Back Skip WAN

Quick Setup - Wireless Configurations

TP-LINK_XXXXWireless Network Name :

Network Authentication:

Wireless Network Key :

********

Enable Wireless:

Back Skip Wi-Fi

(Also called SSID)

Find the SSID (network name) and

Wireless Password printed on the

product label at the bottom of the

modem router.

Click the network icon of your computer or go to Wi-Fi Setting of your

smart device, then select the SSID to join the network.

Computer Smart Device

Connections are available

Wireless Network Connection

Connect automatically

Connect

√

TP-LINK_XXXX

Wi-Fi

TP-LINK_XXXX

CHOOSE A NETWORK...

Other...

< Settings

Configuring the Modem Router

Connecting your computer to the modem router (Wired or

Wireless)

admin

http://tplinkmodem.net

WPA2-Personal (best/recommended)

For technical support and other information, please visit

http://www.tp-link.com/support, or simply scan the QR code.

7106507147 REV8.0.1

Connect a computer to the modem router and the LAN LED lights up.

FAQ (Frequently Asked Questions)

TP-LINK TD-W8960N Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von TP-LINK TD-W8960N

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info