Bedienungsanleitung TP-LINK TL-SF1005P (Seite 2 von 2) (Englisch)

714425

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Frequently Asked Questions (FAQ)

The Power LED should be lit when the power system is working normally.

If the Power LED is not lit, please try the following:

A1:

Make sure the AC power cord is connected to the switch with power

source properly.

A2:

Make sure the voltage of the power supply meets the requirements

of the input voltage of the switch.

A3: Make sure the power source is ON.

Q1. Why is the Power LED not lit?

Please try the following:

A1:

Make sure that the cable connectors are rmly plugged into the

switch and the device.

Make sure the connected device is turned on and works normally.

The cable must be less than 100 meters long (328 feet).

Q2. Why is the Link/Act LED not lit while a device is

connected to the corresponding port?

IEEE802.3i, 802.3u, 802.3x, 802.3af

CSMA/CD

5 10/100Mbps RJ45 Ports, Auto-Negotiation MDI/MDIX

PoE Ports: Port1-Port4, Total Power Supply:58W

10BASE-T: UTP category 3, 4, 5 cable (maximum 100m);

EIA/TIA-568 100Ω STP (maximum 100m)

100BASE-TX: UTP category 5, 5e cable (maximum 100m);

EIA/TIA-568 100Ω STP (maximum 100m)

1Gbps

Store-and-Forward

Automatically learning, automatically aging

External Power Adapter

Input: 100-240VAC, 50/60Hz Output: 48VDC /1.25A

Standard

Protocol

Interface

Network Media (Cable)

Switching Capacity

MAC Address Table

Transfer Method

MAC Address Learning

Power Supply

General Specications

Specications

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may

be required to take adequate measures.

CE Mark Warning

Do not use this product near water, for example, in a wet basement or near a swimming pool.

Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.

SAFETY NOTICES

Cautions

Industry Canada Statement

CAN ICES-3 (B)/NMB-3(B)

Q3. Why is port 4 not supplying power for PoE devices?

If connected PoE device’s total power consumption exceeds 58W, the

system will cut o the power to port 4. For example, port 1, 2 and 4 are

consuming 15.4W respectively, if an additional PoE device with 12W is

inserted to port 3, the system will cut o the power of port 4 to

compensate for the overload.

Operating Temperature

Storage Temperature

Operating Humidity

Storage Humidity

0˚C to 40˚C (32˚F to 104˚F)

-40˚C to 70˚C (-40˚F to 158˚F)

10% to 90%RH non-condensing

5% to 95%RH non-condensing

Environmental and Physical Specications

BSMI Notice

安全諮詢及注意事項

請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。

清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。

注意防潮，請勿將水或其他液體潑灑到本產品上。

插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。

請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。

請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。

Explanation of the symbols on the product label

DC voltage

RECYCLING

This product bears the selective sorting symbol for Waste electrical and electronic equipment

(WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in

order to be recycled or dismantled to minimize its impact on the environment.

User has the choice to give his product to a competent recycling organization or to the retailer when

he buys a new electrical or electronic equipment.

Indoor use only

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та

вимогам, що передбачені чинними законодавчими актами України.

For technical support and other information, please visit

http://www.tp-link.com/support, or simply scan the QR code.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause undesired

operation.

Any changes or modications not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

FCC STATEMENT

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant

provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC and 2011/65/EU.

The original EU declaration of conformity may be found at http://www.tp-link.com/en/ce.

TP-LINK TL-SF1005P Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info