Bedienungsanleitung TP-LINK TL-WR802N (Seite 1 von 2) (Englisch)

605831

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

300Mbps Wireless N Nano Router

Quick

Installation Guide

MODEL NO. TL-WR802N

During Travel

Other Information

REV1.0.4

7106505657

Tips: In this mode, devices can connect to the Internet via the LAN port and wireless simultaneously.

1 Connect the router according to steps A to D in the left diagram.

2 Wait until the router boots up, about 30 seconds, then use the default Wi-Fi Name and Password printed

on the Wi-Fi Info Card to connect to the router.

Check the Internet connection on your laptop or smartphone, and please note that:

- If you can access Internet without any restriction, no other conﬁguration is required.

- If you're redirected to a splash page authentication, please complete it to access the Internet.

- If you want to customize your own wireless network, continue with the steps below.

3 Launch a web browser and type http://tplinkwifi.net into the address bar. Enter admin (in lowercase) for

both user name and password.

4 Click Quick Setup on the left panel, and click Next to start configuring the router. Select Wireless Router

mode and click Next.

5 Select the WAN Connection Type of your Internet Service Provider and follow the screen instructions to

configure the parameters. When using the router in a hotel room or a small office, please select Dynamic

IP.

6 On the Wireless screen, either keep the default Wireless Network Name and Wireless Password or

customize them, then click Next.

7 Click Finish to complete the configuration.

8 Please note the additional steps to be completed once the Nano router is rebooted.

1 Connect the router according to steps A to C in the left diagram.

2 Wait until the router boots up, about 30 seconds, then use the default Wi-Fi Name and Password printed

on the Wi-Fi Info Card to connect to the router.

3 Launch a web browser and type http://tplinkwifi.net into the address bar. Enter admin (in lowercase) for

both user name and password.

4 Click Quick Setup on the left panel, and click Next to start configuring the router. Select Hotspot Router

mode and click Next.

5 Select the

WAN Connection Type of your Internet Service Provider and follow the screen instructions to

configure the parameters. When using the router in a hotel room or a small office, please select

Dynamic

6 Select the public Wi-Fi that you want to connect to, and click Next.

7 Type in the public Wi-Fi password when prompted. In the AP settings section, customize your Wi-Fi

network name and password, then click Next.

8 Click Finish to complete the configuration.

9 Please note the additional steps to be completed once the Nano router is rebooted.

Determine Operation Mode

Wireless Router

Hotspot Router

Range Extender

Client

Access Point

To share a wired (Ethernet) connection to wireless devices, such as in a hotel room, small office, etc.

To create your personal Wi-Fi hotspot from a public Wi-Fi network such as in a hotel room, trade show, etc.

To extend the range of an existing Wi-Fi network.

To function as a wireless adapter to connect your wired device (e.g. Blu-ray® player, smart TV, or game

console) to a wireless network.

To set up a Wi-Fi network from an existing wired (Ethernet) network.

ApplicationOperation Modes

Travel

Home

Wi-Fi Info Card:

Use the default Wi-Fi Name and password

to connect wirelessly.

Description

Port

Functions as the LAN port in Hotspot Router, Range Extender,

and Access Point mode.

Functions as the WAN port in Wireless Router mode.

Power

Reset

LAN/WAN

Connects to a USB charger, power adapter or computer USB

port via the provided Micro-USB cable for power supply.

Resets the router to its factory default settings, please refer

to Frequently Asked Questions (FAQ) for instruction.

IndicationLED Status

Solid

The router is connected to the root Wi-Fi network or Internet.

Blinking

Blinking steadily: The router is disconnected from the root Wi-Fi

network or Internet.

Blinking irregularly: The router is booting or updating firmware.

Wi-Fi Name(SSID):TP-LINK_XXXX

Wi-Fi Password/PIN:XXXXXXXX

300Mbps Wireless N Nano Router

(SSID):

/PIN

802

Router Ports and LED: Using Amazon Fire TV Stick or Chromecast

when traveling:

Connect your laptop, smartphone or

tablet to the router.

Plug the HDMI streaming stick directly

into the hotel TV.

Follow the onscreen instruction to

connect to the router’s Wi-Fi.

Enjoy streaming content on the TV.

LED

Wireless Router (Default)

Hotspot Router

If you change the default Wi-Fi name and password, you will need to reconnect your wireless

devices to the new Wi-Fi network.

If you change the default Wi-Fi name and password, you will need to reconnect your wireless

devices to the new Wi-Fi network.

Public

Wi-Fi Network

Name

TL-WR802N's

Wi-Fi Name:

TP-LINK_XXXX

B C

Public

Wi-Fi

TL-WR802N’s

Wi-Fi Name:

TP-LINK_XXXX

B C

Internet

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

TP-LINK TL-WR802N Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von TP-LINK TL-WR802N

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info