Bedienungsanleitung Traeger COM200 - Large Commercial Trailer (Seite 14 von 17) (Englisch)

798767

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

Still no Pellets in the Firepot – Proceed to step 3.

3) Disconnect Power Cord from electrical outlet.

a) Unplug the Auger Drive Motor ( Red/White wire pair connector) and the Draft

Induction Fan (Orange/White wire pair connector).

b) Reconnect the Draft Induction Fan to the Red/White wire pair and the Auger

Drive Motor to the Orange/White pair.

c) Plug Power Cord into an appropriate, grounded electrical outlet and turn the

Switch/Dial ON.

d) If the Auger Drive Motor is operating (check the small fan blade on the back of

the motor), the problem is in the Three Speed or Digital Control, which will need

to be replaced. Contact your Traeger Dealer or the Traeger Parts

Department (SECTION SEVEN) to place an order.

4) If the Auger Drive Motor is not operating but the Draft Induction Fan is operating,

the problem is in the Auger system, which will need to be checked.

a) With the Switch/Dial OFF, locate the small fan blade on the back of the Auger

Drive Motor.

b) While watching the fan blade, turn the Switch/Dial to ON. If the fan blade does

not turn, turn the Switch/Dial to OFF. This indicates a defective Auger Drive

Motor and it will need to be replaced. Contact your Traeger Dealer or the

Traeger Parts Department (SECTION SEVEN) to place an order.

c) If the fan blade turns a bit and then stops, continue watching and turn the

Switch/Dial to OFF. If the fan blade UNWINDS slightly, this indicates a jam in

the Auger system which will need to be cleared.

d) Disconnect Power Cord from electrical outlet and remove Pellets from the Pellet

Hopper. Check for foreign objects and wet/decomposed Pellets, both of which

can cause a jam in the Auger system. The Auger will need to be removed to

clear a jam in the Auger system. See “HOW DO I REMOVE THE AUGER IF IT

JAMS?” section below.

HOW DO I REMOVE THE AUGER IF IT JAMS?

For models with a fixed Auger Drive Motor:

1) Remove any covers necessary to access the Auger Drive Motor.

2) Remove the screw connecting the Auger Drive Motor shaft to the Auger shaft, using

a 7/64 hex wrench and a 5/16 wrench or driver.

3) Remove two bolts mounting the Auger Drive Motor/Bracket assembly to the Burner

Box with a 7/16 wrench.

4) With a small pipe wrench or locking pliers on the Auger shaft, turn the Auger counter

clockwise. It will turn hard until it breaks free, then the Auger will turn freely.

5) Remove the Auger and clean all Pellets, ash or foreign objects from the Auger,

Auger Tube and Firepot. A shop-vac is ideal tor this task.

6) Sand the outside surfaces of the auger with medium grit sandpaper. Check the

inside of the Auger Tube and sand it if needed. Vacuum sanding grit from the Auger

Tube and Firepot when finished.

7) Reinstall the Auger into the Auger Tube, making sure that it rotates freely.

8) Re-attach the Auger Drive Motor/Bracket assembly, ensuring that the Auger shaft

rotates freely on the Auger Drive Motor Shaft. Re-attach the Auger shaft to the

Auger Drive Motor shaft.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Traeger COM200 - Large Commercial Trailer Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info