Bedienungsanleitung Traeger Li Tex - BBQ07E.02 (Seite 19 von 24) (Englisch)

798764

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

and it will need to be replaced. Contact your Traeger Dealer or the Traeger Parts

Department (Section Seven) to place an order.

c) If the fan blade turns a bit and then stops, continue watching and turn the Switch

OFF (o). If the fan blade UNWINDS slightly, this indicates a jam in the Auger system

which will need to be cleared.

d) DANGER! Turn the Switch OFF (o) and disconnect the Power Cord. Remove the

Pellets from the Pellet Hopper. Check for foreign objects and wet or decomposed

Pellets, both of which can cause a jam in the Auger system. The Auger will need to

be removed to clear a jam in the Auger system. See “HOW DO I REMOVE THE

AUGER IF IT JAMS?” section below.

HOW DO I REMOVE THE AUGER IF IT JAMS?

1) DANGER! Turn the Switch OFF (o) and disconnect the Power Cord.

2) CAUTION! If the Grill is still hot, allow it to thoroughly cool.

3) Remove any covers necessary to access the Auger Drive Motor.

4) Remove the screw connecting the Auger Drive Motor shaft to the Auger shaft and

the screw retaining the Auger Bushing into the Auger Tube.

5) With a small pipe wrench or locking pliers on the Auger shaft, turn the Auger counter

clockwise. It will turn hard until it breaks free, then the Auger will turn freely.

6) Remove the Auger and clean all Pellets, ash or foreign objects from the Auger,

Auger Tube and Firepot. (See instructions for proper handling and disposal of

ash in Section Five)

7) Sand the outside surfaces of the auger with medium grit sandpaper. Check the

inside of the Auger Tube and sand it if needed. Vacuum the sanding grit out of the

Auger Tube and Firepot when finished. Check that the Auger rotates freely.

9) Re-attach the Auger shaft to the Auger Drive Motor shaft.

WHY DOES MY GRILL FIRE GO OUT ON “SMOKE” SETTING?

The “P” number for the Smoke Adjustment on the Digital Control may be set too high.

Review the Digital Thermostat Control Functions in Section Four: Operating Tips

to make an adjustment.

There may be excess ash in the Firepot which needs to be cleaned.

WARNING! If the fire in the Firepot goes out while smoking, when sufficient Pellets

are still in the Pellet Hopper, it is important to follow these steps. Failure to do so

may cause a hazardous “over-firing” of your grill due to an excess of unburned

pellets in the Firepot.

a) DANGER! Turn the Switch OFF (o) and disconnect the Power Cord. If the Grill is

still hot, allow it to thoroughly cool. Open the Door and remove all food, the Porcelain

Grill, Grease Drain Pan and the Heat Baffle.

b) WARNING! Remove all unburned pellets and ash from inside and around the

Firepot. (See instructions for proper handling and disposal of ash in Section

Five)

c) Before replacing the Heat Baffle, Grease Drain Pan and the Porcelain Grill, plug

the Power Cord into an appropriate, grounded electrical outlet and turn the Switch

ON (--). Pellets should fall into the Firepot and the Hot Rod should begin to heat (it

will start to turn red). CAUTION! Do not touch it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Traeger Li Tex - BBQ07E.02 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info