Bedienungsanleitung Traeger Select Pro - BBQ400.03 (Seite 13 von 18) (Englisch)

798690

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

4) If the Auger Drive Motor is not operating but the Draft Inducer Fan is operating, the

problem is in the Auger system, which will need to be checked.

a) With the Power Switch and the Switch/Dial OFF, locate the small fan blade

on the back of the Auger Drive Motor.

b) While watching the fan blade, turn the Power Switch and then the Switch/Dial to

ON. If the fan blade does not turn, turn the Switch/Dial to OFF. This indicates a

defective Auger Drive Motor and it will need to be replaced. Contact your

Traeger Dealer or the Traeger Parts Department (SECTION SEVEN) to place

an order.

c) If the fan blade turns a bit and then stops, continue watching and turn the

Switch/Dial to OFF. If the fan blade UNWINDS slightly, this indicates a jam in

the Auger system which will need to be cleared.

d) Disconnect Power Cord from electrical outlet and remove Pellets from the Pellet

Hopper. Check for foreign objects and wet/decomposed Pellets, both of which

can cause a jam in the Auger system. The Auger will need to be removed to

clear a jam in the Auger system. See “HOW DO I REMOVE THE AUGER IF IT

JAMS?” section below.

HOW DO I REMOVE THE AUGER IF IT JAMS?

1) Remove any covers necessary to access the Auger Drive Motor.

2) Remove the screw connecting the Auger Drive Motor shaft to the Auger shaft and

the screw retaining the Auger Bushing into the Auger Tube.

3) With a small pipe wrench or locking pliers on the Auger shaft, turn the Auger counter

clockwise. It will turn hard until it breaks free, then the Auger will turn freely.

4) Remove the Auger and clean all Pellets, ash or foreign objects from the Auger,

Auger Tube and Firepot. A shop-vac is ideal for this task.

5) Sand the outside surfaces of the auger with medium grit sandpaper. Check the

inside of the Auger Tube and sand it if needed. Vacuum the sanding grit out of the

Auger Tube and Firepot when finished.

6) Reinstall the Auger Bushing and the Auger into the Auger Tube, making sure that

the Auger rotates freely.

7) Re-attach the Auger shaft to the Auger Drive Motor shaft.

WHY DOES MY GRILL FIRE GO OUT ON “SMOKE” SETTING?

Excess ash in the Firepot may be the problem.

1) Open the Door/Lid and remove the Porcelain Grill, Grease Drain Pan and Heat

Baffle from inside the Grill.

2) IMPORTANT: Remove all unburned Pellets and ash from inside and around

the Firepot. A shop-vac is ideal for this task CAUTION! ASSURE THAT THE

GRILL IS COLD TO AVOID A FIRE FROM HOT ASH.

3) Replace the Heat Baffle, Grease Drain Pan and the Porcelain Grill and initiate start-

up procedure.

4) If this didn’t remedy the problem, contact Traeger Technical Support (SECTION

SEVEN) for additional troubleshooting help.

WITH THE TRAEGER DIGITAL CONTROL, WHAT DIAL SETTING IS

RECOMMENDED FOR STARTING THE GRILL?

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Traeger Select Pro - BBQ400.03 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info