Bedienungsanleitung Traeger Texas Elite - TFB65LZB (Seite 9 von 22) (Englisch)

798761

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

SECTION THREE: SUBSEQUENT START-UP

With the Door open, turn the Switch ON (--) and the Temperature/Dial to SMOKE. In

approximately 2 minutes you will notice whitish-gray smoke coming out of the Grill

as the Pellets ignite. After assuring the Pellets have ignited, close the Door and set

the Temperature/Dial to any cooking setting desired. The Grill should be allowed to

pre-heat for approximately 10 minutes with the Door closed before placing food in

the Grill.

WARNING! If at any time, the Grill fails to light or the fire in the Firepot goes out while

cooking or smoking, when sufficient pellets are still in the Pellet Hopper, it is important

to follow these steps. Failure to do so may cause a hazardous “over-firing” of your grill

due to an excess of unburned pellets in the Firepot.

1) DANGER! Turn the Switch OFF (o) and disconnect the Power Cord. If the Grill is still

hot, allow it to thoroughly cool. Open the Door and remove all food, the Porcelain

Grill, Grease Drain Pan and the Heat Baffle.

2) WARNING! Remove all unburned pellets and ash from inside and around the

Firepot. (See instructions for proper handling and disposal of ash in Section

Five)

3) Before replacing the Heat Baffle, Grease Drain Pan and the Porcelain Grill, plug the

power Cord into an appropriate, grounded electrical outlet and restart the Grill. Pellets

should fall into the Firepot and the Hot Rod should begin to heat (it will start to turn

red). CAUTION! Do not touch it.

4) If this procedure is successful, you will soon see flames come out of the Firepot.

Then turn the Switch OFF (o), and let the Grill cool down. Position the Heat Baffle,

the Grease Drain Pan and Porcelain Grill in their proper locations. With the Door

open, turn the Switch ON (--) and the Temperature/Dial to SMOKE. In approximately

2 minutes you will notice whitish-gray smoke coming out of the Grill as the Pellets

ignite. After assuring the Pellets have ignited, close the Door and set the

temperature/Dial to any cooking setting desired.

5) If this procedure is not successful, see Section Six: FREQUENTLY ASKED

QUESTIONS for troubleshooting tips or contact Traeger Technical Support (Section

Seven) to help diagnose the problem before proceeding to the MANUAL LIGHTING

INSTRUCTIONS below.

MANUAL LIGHTING INSTRUCTIONS:

If the Hot Rod only is not operating, the Grill can still be used to cook and smoke using

the MANUAL LIGHTING PROCEDURE below:

1) DANGER! Turn the Switch OFF (o) and disconnect the Power Cord. Allow the Grill to

thoroughly cool if it is still hot. From beneath the Pellet Hopper, disconnect the Hot

Rod (Purple / White wire pair as shown in the wiring diagram near the end of this

manual). You will need to remove the Hopper Bottom Panel to access the wiring.

Once the Hot Rod is disconnected, replace the Hopper Bottom Panel and plug the

Power Cord back into an appropriate, grounded electrical outlet.

2) Open the Pellet Hopper and fill with TRAEGER BBQ PELLETS.

WARNING! USE ONLY TRAEGER BRAND BBQ WOOD PELLETS, which are

specifically made to work in our Grills. NEVER use heating fuel pellets in the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Traeger Texas Elite - TFB65LZB Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info