Bedienungsanleitung Traeger XL - BBQ150.01 (Seite 19 von 24) (Englisch)

798768

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

d) Disconnect Power Cord from electrical outlet and remove Pellets from the Pellet

Hopper. Check for foreign objects and wet/decomposed Pellets, both of which can

cause a jam in the Auger system. The Auger will need to be removed to clear a jam in

the Auger system. See “HOW DO I REMOVE THE AUGER IF IT JAMS?” section

below.

`HOW DO I REMOVE THE AUGER IF IT JAMS?

1) Remove any covers necessary to access the Auger Drive Motor.

2) Remove the screw connecting the Auger Drive Motor shaft to the Auger shaft and the

screw retaining the Auger Bushing into the Auger Tube.

3) With a small pipe wrench or locking pliers on the Auger shaft, turn the Auger counter

clockwise. It will turn hard until it breaks free, then the Auger will turn freely.

4) Remove the Auger and clean all Pellets, ash or foreign objects from the Auger, Auger Tube

and Firepot. A shop-vac is ideal tor this task.

5) Sand the outside surfaces of the auger with medium grit sandpaper. Check the inside of the

Auger Tube and sand it if needed. Vacuum the sanding grit out of the Auger Tube and

Firepot when finished.

6) Reinstall the Auger Bushing and the Auger into the Auger Tube, making sure that the Auger

rotates freely.

7) Re-attach the Auger shaft to the Auger Drive Motor shaft.

WHY DOES MY GRILL FIRE GO OUT ON “SMOKE” SETTING?

Excess ash in the Firepot may be the problem.

1) Open the Door and remove the Porcelain Grill, Grease Drain Pan and Heat Baffle from

inside the Grill.

2) IMPORTANT: Remove all unburned Pellets and ash from inside and around the

Firepot. A shop-vac is ideal tor this task CAUTION! ASSURE THAT THE GRILL IS COLD

TO AVOID A FIRE FROM HOT ASH.

3) Replace the Heat Baffle, Grease Drain Pan and the Porcelain Grill and initiate start-up

procedure.

4) If this didn’t remedy the problem, contact Traeger Technical Support (SECTION SEVEN)

for additional troubleshooting help.

WITH THE TRAEGER DIGITAL CONTROL, WHAT DIAL SETTING IS RECOMMENDED

FOR STARTING THE GRILL?

The auto-start procedure is the same for all Grill Controls. With the Door open, turn the

Switch/Dial ON and Temperature Dial to SMOKE. In approximately 2 minutes you will

notice whitish-gray smoke coming out of the Grill as the Pellets ignite. After assuring the

Pellets have ignited, close the Door and set the Temperature Dial to any cooking setting

desired.

HOW DO I PROTECT MY PAINT FINISH?

1) Use a protective Cover on the Grill and touch-up paint to repair any scratches. A

TRAEGER GRILL COVER to protect the Grill is highly recommended! Covers and

touch-up paint are available from your Traeger Dealer, or log on to our Web Site –

www.traegergrills.com.

2) Every 90 days, use a high quality car wax on the outside surfaces of the Grill. ONLY

APPLY WAX TO A COLD GRILL.

WHERE CAN I GET A NEW PART FOR MY GRILL?

Check with your Traeger Dealer. They may have the part in stock or can order the part for you.

Or you can contact the Traeger Parts Department (SECTION SEVEN) to place an order. In

either case, please provide your name, phone number, address, Model and Serial Number of

the Grill (located on a label inside the Hopper Lid), along with the part identification.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Traeger XL - BBQ150.01 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info