Bedienungsanleitung Trek eBike Systems 2023 - Bosch (Seite 24 von 376) (Deutsch, Englisch, Holländisch, Französisch)

817492

Zoom out

Zoom in

Vorherige Seite

1/376

Nächste Seite

English – 4

Switching bike lights on/off

On the model in which the lighting is powered by the eBike

system, the front and rear lights can be switched on and off

at the same time via the on-board computer using the bike

lights button(2).

Check that your bike lights are working correctly before

every use.

When the lighting is switched on, <Lights on> appears and

when the lighting is switched off, <Lights off> appears for

approx. 1s on the text indicator (d). The lighting symbol (c)

is displayed when the light is on.

The on-board computer saves the light status and activates

this saved status accordingly after a restart.

Switching the bike lights on and off has no effect on the

backlighting of the display.

Switching the push assistance on/off

The walk assistance makes it easier to push your eBike. The

speed in this function depends on the selected gear and can

reach a maximum of 6km/h.

uThe push assistance function must only be used when

pushing the eBike. There is a risk of injury if the wheels

of the eBike are not in contact with the ground while using

the push assistance.

To activate the walk assistance, briefly press the WALK but-

ton on your on-board computer. Once it is activated, press

the + button within 10s and keep it held down. The eBike

drive is now switched on.

Note: The push assistance cannot be activated at assistance

level OFF.

The walk assistance is switched off as soon as one of the fol-

lowing occurs:

– You release the+button(12),

– the wheels of the eBike are locked (e.g. by applying the

brakes or hitting an obstacle),

– the speed exceeds 6km/h.

The push assistance function is subject to local regulations;

the way it works may therefore differ from the description

above, or the function may even be deactivated completely.

Powering external devices via the USB port

The USB port can be used to operate or charge most devices

that can be powered via USB (e.g. various mobile phones).

Charging requires the on-board computer to be mounted

and a sufficiently charged eBike battery to be inserted in the

eBike.

Open the protective cap(8) for the USB port on the on-

board computer. Use a MicroA – MicroB USB charging

cable (available from your Bosch eBike dealer) to connect

the USB port on the external device to the USB port(7) on

the on-board computer.

Once the electrical load has been disconnected, the USB

port must be carefully resealed with the protective cap(8).

uUSB connections are not waterproof. When cycling in

the rain, do not connect any external devices and

make sure that the USB port is fully sealed by the pro-

tective cover(8).

Important: If electrical loads are connected, this can affect

the range of the eBike.

Displays and configurations of the

on-board computer

Speed and distance indicators

The speedometer (f) always displays the current speed.

You can choose from the following functions in the function

display (combination of text indicator (d) and value indic-

ator (e)):

–<Clock>: Current time

–<Max. speed>: Maximum speed achieved since the last

reset

–<Avg. speed>: Average speed achieved since the last re-

set

–<Trip time>: Journey time since the last reset

–<Range>: Estimated range of the available battery

charge (at constant conditions such as assistance level,

route profile, etc.)

–<Odometer>: Total distance travelled with the eBike

(cannot be reset)

–<Trip distance>: Distance travelled since the last reset

To switch between display functions, press the ibut-

ton(1) on the on-board computer or the ibutton(10) on the

operating unit repeatedly until the required function is dis-

played.

To reset the <Trip distance>, <Trip time> and <Avg.

speed>, switch to one of these three functions and then

press the RESET button (6) until the indicator is set to zero.

This will also reset the values of the other two functions.

To reset the <Max. speed>, switch to this function and then

press the RESET button (6) until the indicator is set to zero.

To reset the <Range>, switch to this function and then press

the RESET button (6) until the indicator is reset to the value

of the factory setting.

If the on-board computer is removed from the holder (4), all

values of the functions are saved and can still be displayed.

Displaying/adjusting basic settings

The basic settings can be displayed and changed regardless

of whether the on-board computer is inserted in the

holder(4) or not. Some settings can only be viewed and

changed when the HMI is inserted. Depending on the equip-

ment of your eBike, some menu items may not be present.

To go to the basic settings menu, simultaneously press the

RESET button(6) and the i button(1) until<Configura-

tion> appears on the text indicator(d).

To switch between the basic settings, press the i but-

ton(1) on the on-board computer repeatedly until the re-

quired basic setting is displayed. If the on-board computer is

inserted in the holder(4), you can also press the i but-

ton(10) on the operating unit.

1 270 020 XBI | (14.02.2023) Bosch eBike Systems

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trek eBike Systems 2023 - Bosch Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info