Bedienungsanleitung Trek Incite 11i - 2005 (Seite 3 von 10) (Englisch)

775420

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

INSTALLATION

Tools needed:

• Electrical tape

• Slot-type screwdriver

• Phillips-type screwdriver

• Scissors

This section explains the steps to install your computer onto your bicycle:

• Placing the computer on the handlebar

• Placing the magnet and sensor(s) on the bike

Placing the computer on the handlebar

The Trek Incite computer can be mounted on the handlebar or on the stem (Figure

3).

To install the computer on the handlebar

1. Determine your bicycle’s handlebar diameter: 22.2mm, 25.4/26.0mm, or 31.8mm.

2. Select the corresponding bar clamp

For a 22.2mm bar, use the rubber shim (provided) inside the smaller clamp.

3. Insert the handlebar clamp into the back of the computer base (Figure 4) and

slide it towards the front of the base.

4. Insert the rubber friction pad into the computer base, aligned across the

computer base.

5. With the wire pointing toward the front of the bike, wrap the bar clamp around

the handlebar.

6. Insert the screw through the washer and into the computer base.

7. Tighten the screw until the computer base cannot rotate on the handlebar.

8. Slide the computer into the computer base until the front of the computer and

computer base line up.

9. Check that the computer base cannot be rotated around the handlebar, and that

the computer cannot slide backwards on the computer base (Figure 5).

To install the computer on the stem

1. Insert the rubber friction pad into the computer base, aligned along the

computer base.

2. Insert two nylon ties through the computer base (Figure 6).

3. Place the base on the stem and tighten the nylon tie.

4. Slide the computer into the computer base until the front of the computer and

computer base line up.

5. Check that the computer base cannot be rotated around the stem and the

computer cannot slide backwards on the computer base.

6. Tighten the nylon ties and trim the excess length.

Placing the magnet and sensor(s) on the bike

The wheel magnet must be aligned so that it passes across the sensor. As the

magnet passes the sensor, it must be no further from the sensor than 1 to 3mm (1/

32 to 1/8 inch).

The wheel magnet has a ‘T’ shaped slot with two configurations: round spokes and

flat or bladed spokes (Figure 7).

Computers with the cadence function have two sensors. The shorter computer

wire is for the cadence sensor which mounts near the crankset. The sensor must be

aligned so that the magnet passes within 1-3mm of the sensor, and in line with

the small line on the sensor (Figure 8).

To install the magnet

1. Remove the screw from the magnet.

2. Slide the slot in the back of the magnet over the spoke.

For a flat or bladed spoke, start the spoke near the end where the spoke is round, and align the

top of the ʻTʼ with the spoke as you slide the magnet up the blade.

3. Thread the screw into the magnet until it is snug against the spoke.

Installation

Figure 6- Nylon tie

threaded through com-

puter base

Figure 7- Magnet placed

on round and oval

spokes

Figure 3- Computer on

handlebar and stem

Figure 4- Clamp and

friction pad in computer

base

Figure 5- Make sure the

computer cannot be

bounced off.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trek Incite 11i - 2005 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info