Bedienungsanleitung Trek Ride plus - E-bike (Seite 36 von 40) (Englisch)

516339

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

EN-33

ENGLISH

7. Problem solving

7.1 Drive problems

• The Service Indication is visible on the display of the controller.

Whenitshows,thismeansthattheelectronicsystemrecognizesaproblem.Firsttrysolvingthe

problem by switching the RIDE+ system Off and back On. If the error persists, visit your dealer

immediately for repairs.

TheServiceIndicationcanmeanthebatterypackhasbeenimpactedormis-handled,causingan

electrical fault. In an extremely rare case, a battery pack that has been severely impacted or

otherwisemis-handledcouldpotentiallycatchfire.Inanemergencysituation,fullyimmersethe

battery pack in a large container of water.

• The system will not switch On (no beep from the battery pack), the LCD display remains blank

Firstcheckthebatterypack.Itmustbeinplaceandthelockmustbepushedinfully.Checkall

connectorsanddisconnectandreconnectifnecessary.Makesurethatthecontrollerisslidintoits

docking all the way. If this does not help, contact your dealer.

• The motor is always in generative mode

Thereisprobablysomethingwrongwiththeswitchforgenerativebrakingintheright-handbrake

lever. If there is something wrong with the generative braking switch, try switching the system Off

and On again. If this does not help, unplug the connector between brake lever and controller.

Thisshouldsolvetheproblem,butgenerativebrakingwillbedisabled.Contactyourdealer.

• After a repair or service, the motor is not as powerful as it was earlier

Onabikewitharearmotor,havetherearaxlenutstightenedtothecorrecttorque(40Nm).

On a bike with a front motor, have the front as well as the rear axle nuts tightened to the correct

torque(40Nm).

• The system does assist, but irregularly

Onabikewitharearmotor,havetherearaxlenutstightenedtothecorrecttorque(40Nm).

Onabikewithafrontmotor,havethefront-aswellastherearaxlenutstightenedtothecorrect

torque(40Nm).Checkallconnectionsofthesystem.

• System switches On as battery pack is put into the docking station

This happens sometimes due to static electricity. There is no problem with the system.

7.2 Charging problems

• The display does not show ‘full’ after a complete recharge

Please make sure you are following all charging instructions.

Let the battery pack cool down for several hours and try again. If the problem persists, fully

discharge(byriding)andrechargethebatterypack,ifnecessaryhaveyourdealerupdateittothe

latest firmware.

• The charging light does not turn red after connecting the power cable to the power source

Checkthepowercabletothepowersupply.Ifdefective,replacethecableimmediately.

WARNING. Replace a damaged power cable immediately to prevent an electric shock.

problem solvIng

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trek Ride plus - E-bike Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trek Ride plus - E-bike

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info