Bedienungsanleitung Trendnet TEW-712BR (Seite 22 von 51) (Englisch)

541687

Zoom out

Zoom in

Vorherige Seite

1/51

Nächste Seite

TRENDnet User’s Guide

TEW-712BR

• RTS Threshold – The Request To Send (RTS) function is part of the networking

protocol. A wireless device that needs to send data will send a RTS before sending

the data in question. The destination wireless device will send a response called

Clear to Send (CTS). The RTS Threshold defines the smallest data packet size

allowed to initiate the RTS/CTS function.

Default Value: 2346 (range: 0-2347)

• Fragmentation Threshold – Fragmentation in wireless networks is the process of

breaking down data communications into smaller data packets in order to

improve data efficiency when transferring or receiving data between wireless

devices. The fragmentation threshold defines the maximum size of the data

packets that are broken down.

Default Value: 2346 (range: 256~2346, even numbers only)

• DTIM Interval – A Delivery Traffic Indication Message (DTIM) is an informational

message that is sent as part of a beacon by an access point (your wireless router)

to a wireless client (wireless device or connecting station) in sleep mode to

provide an alert that data is awaiting delivery. The DTIM Interval (also called Data

Beacon Rate) is the amount of time between DTIM transmissions included in part

of a beacon.

Default Value: 1 (range: 1-255)

Access Control Filters

Access control basics

Access > Filter

MAC address filters

Access > Filter > MAC Filters

Every network device has a unique, 12-digit MAC (Media Access Control) address. Using

MAC filters, you can allow or deny specific computers and other devices from using this

router’s wired or wireless network.

1. Log into your router management page (see “

Access your router management page”

on page 24).

2. Click on Access, click on Filter, and click on MAC Filters.

3. Add the MAC addresses to the MAC Table first before applying the MAC filter

function.

Note: MAC filter can be configured to allow access to the listed MAC address and

deny all others unlisted or vice versa. The recommended function is to choose to

only allow access to the MAC addresses listed and deny all others unlisted because it

is easier to determine the MAC addresses of devices in your network then to

determine which MAC addresses you do not want to allow access.

• Name – Enter a name for the MAC address entry.

• MAC Address – Enter the 12-digit MAC address.(e.g. 00-11-22-AA-BB-CC)

Note: You can check the Dynamic DHCP List for the MAC addresses of the devices on

your network, see “

Setup the DHCP server on your router” on page 27 or refer to your

computer or device documentation to find the MAC address.

Click Add to save the new MAC address entry to the MAC Table. After clicking Add, the

MAC address entry will appear in the list below. Repeat for each device.

• Add – Saves a new MAC address entry.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trendnet TEW-712BR Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trendnet TEW-712BR

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info