Bedienungsanleitung Trendnet TPL-4052E (Seite 11 von 30) (Englisch)

541084

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

TPL-4052E User’s Guide Securing Your Powerline Network

Conguring an addional Powerline Adapter to connect and

use the network name of your exisng powerline network:

Note: Use the Sync buon procedure below if you are connecng

TRENDnet Powerline models TPL-401E, TPL-402E, TPL-405E , TPL-406E ,

TPL-407E or TPL-4052E.

1� Verify that all exisng Powerline Adapters are already installed and

connected�

Prepare your adapter:

2� Push and hold the Sync buon on the addional Powerline Adapter

for 15 seconds and then release it. All LEDs will turn o and turn

back on. This will erase the current network name assigned to the

addional Powerline Adapter.

Start associaon:

3� Push and hold the Sync buon on one of the exisng Powerline

Adapters connected to your powerline network for 2 seconds and

then release it. The Power (PWR) LED will start blinking.

4� Within 2 minutes, push and hold the Sync buon on the addional

Powerline Adapter for 2 seconds and release it. The Power

(PWR) LED will start blinking. This will recongure your addional

Powerline Adapter to connect and use the network name of your

exisng powerline network. All LEDs will turn o and turn back on

and the Powerline (PL) LED will turn on the adapters are connected.

Congure to add addional Powerline Adapters to your exisng

powerline network, repeat the steps above for each adapter.

Using the Powerline Ulity

The Powerline Ulity allows you doing following jobs:

1� Create a customized network name for your powerline network

and apply it to mulple Powerline Adapters at the same me.

2� View Powerline Adapters connected to your network (using

the MAC address) and the approximate connecon quality and

speed of each Powerline Adapter.

3� View and upgrade Powerline Adapter rmware.

Note: Link speed displayed in the ulity of your Powerline

Adapters to another through your electrical system is esmated.

Actual link speed may vary.

Beforeinstallingandusingtheulity,pleaseensurethefollowing:

1. Write down the DevicePassword(DPW) (16-digit characters

A-Z only) and MAC Address (12-digit characters a-f, A-F, 0-9) of

each Powerline Adapter as this will be required to change the

network name for mulple Powerline Adapters. See “Product

informaon on device label” on page 2.

2. Make sure your computer in which you are installing the ulity

is connected to your network and your Powerline Adapters are

also connected to your network.

3. If you have changed your network name using the Sync buon

and you are creang a customized network name, it is required

to reset all powerline devices to factory defaults using the

physical Reset buon on your Powerline Adapter before using

the ulity. See”Push Buons” on page 3.

4. Please ensure that your Powerline Adapters are already

installed and connected and the Ethernet port on each adapter

is connected to a device powered on.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trendnet TPL-4052E Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info