Bedienungsanleitung Tristar st 8229 (Seite 6 von 20) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

324036

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Operation and maintenance

Remove all packaging of the device.

Check if the voltage of the appliance corresponds to the main voltage of your home.

Rated voltage : AC220-240V 50Hz.

Anti-calk system

A special resin filter inside the water reservoir softens the water and prevents scale build-up in

the plate. The resin filter is permanent and does not need replacing.

Please note:Use tap water only. Distilled and/demineralised water makes the “Zero-Calc” anti-

calc system ineffective by altering its physicochemical characteristics.

Do not use chemical additives, scented substances or decalcifiers. Failure to comply with the

above-mentioned regulations leads to the loss of guarantee.

Anti-drip system

With the anti-drip system, you can perfectly iron even the most delicate fabrics.

Always iron these fabrics at low temperatures. The plate may cool down to the point where no

more steam comes out, but rather drops of boiling water that can leave marks or stains. In

these cases, the Anti-drip system automatically activates to prevent vaporization, so that you

can iron the most delicate fabrics without risk of spoiling or staining them.

General instruction

When using the iron for the first time, you may notice a slight emission of smoke and hear

some sounds made by the expanding plastics. This is quite normal and it stops after a short

time. We also recommend passing the iron over an ordinary cloth before using it for the first

time.

Preparations

Soft the laundry to be ironed according to the international symbols on the garment label, or if

this is missing, according to the type of fabric.

GARMENT

LABEL

FABRIC

TYPE

THERMOSTAT REGULATION

synthetic

low temperature

silk - wool

··

medium temperature

Cotton - linen

···

high temperature

Fabric not to be ironed

Start ironing the garments requiring a low temperature.

This reduces the waiting times (the iron takes less time to heat up than to cool down) and

eliminates the risk of scorching the fabric.

Steam ironing

Filling the reservoir

- Check that the plug is disconnected from the socket.

- Move the steam selector (3) to “0” [Fig. 1].

- Open the lid (2).

- Raise the tip of the iron to help the water enter the opening without overflowing.

- Slowly pour the water into the reservoir using the special measure (15) and taking care not to

go over the maximum level (about 300ml) indicated by “MAX” on the reservoir [Fig. 2].

- Close the lid (2).

Selecting the temperature.

- Put the iron in a vertical position.

- Put the plug in the socket.

- Adjust the thermostat knob (11) according to the international symbol on the garment label

[Fig. 3]. The plate temperature control light (9) indicates that the iron is heating up. Wait until

the plate temperature control light goes off before ironing.

Warning: during ironing, the plate temperature control light (9) comes on at intervals, indicating

that the selected temperature is maintained. If you lower the thermostat temperature after

ironing at a high temperature, do not start ironing until the plate temperature control light

comes on again.

Selecting the steam.

The quantity of steam is regulated by the steam selector (3).

Move the steam selector to a position between minimum and maximum depending on the

quantity of steam required and

the temperature selected [Fig. 1].

Warning: the iron gives off steam continuously only if you hold the iron horizontally. You can

stop the continuous steam by placingthe iron in a vertical position or by moving the steam

selector to “0”. As indicated on the thermostat knob (11) and in the initial table, you can only

use steam at the highest temperatures. If the selected temperature is too low, water may drip

onto the plate.

Selecting Shot-steam and steam when ironing vertically.

Press the shot-steam button (5) to generate a powerful burst of steam that can penetrate the

fabrics and smooth the most difficult and tough creases. Wait for a few seconds before

pressing again [Fig. 4].

By pressing the shot-steam button at intervals you can also iron vertically (curtains, hung

garments, etc.) [Fig. 5].

Warning: the shot-steam function can only be used at high temperatures. Stop the emission

when the plate temperature control light (9) comes on, than start ironing again only after the

light has gone off.

Dry ironing

To iron without steam, follow the instructions in section “steam ironing”, leaving the steam

selector (3) on position “0”.

Spray Function

Make sure that there is water in the reservoir. Press the spray button (4) slowly (for a dense

spray) or quickly (for a vaporized spray) [Fig. 6].

Warning: for delicate fabrics, we recommend moistening the fabric beforehand using the spray

function (4), or putting a damp cloth between the iron and the fabric. To avoid staining, do not

use the spray on silk or synthetic fabrics.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tristar st 8229 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info