Bedienungsanleitung Tristar sz 2187 (Seite 6 von 41) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

320930

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

Operation and maintenance

Remove all packaging of the device.

Check if the voltage of the appliance corresponds to the main voltage of your home.

Rated voltage : AC220-240V 50Hz

This vacuum is not designed to collect liquids and sharp. Never vacuum hot ashes, make sure

it is fully cooled.

First use

Place the vacuum foot (No 15) on the telescope tube (nr.7). The telescope tube length can be

made, according to your wishes, by the pressing button (nr.6) down and push the tube to

extend or reduce. Place the tube (Nr.10) with the side of the hose coupling (nr.5) in front of the

vacuum, if you hear a click, this just confirmed. To disconnect the hose press the button of the

hose coupling.

Using the button on the vacuum foot in the desired position, with or without a brush on the

bottom of the suction foot.

With the air regulator (nr.8) controls the suction if it should be

temporarily reduced.

Use

Pull the plug from the vacuum cleaner and place it into a wall outlet. Press the ON / OFF

button and start your vacuum cleaner line to the suction button (nr.2) the desired suction.

With the air regulator (nr.8) controls the suction if it should be temporarily reduced.

To turn the unit off, press the ON / OFF button. Unplug the power cord and press the button

cable rewind (nr.3). You can use the storage clip (nr.14) to store the vacuum bar when you

store the vacuum cleaner.

Cleaning of the device

You need to empty the dust container when the dust full indicator light (No 4) lights.

Do this immediately otherwise it loses much suction device.

Press the button of the dust collector as

Figure B and remove it from the device.

Hold the container over a dust bin

and press the button at the bottom of the dust

collector. See Figure C.

Close the lid and place the dust collector

back into the device until you hear a click.

To ensure the best suction of the vacuum cleaner you have to cleanthe HEPA filter (Nr.12)

regular. Remove the dust container from the device (Figure B). Turn the lid counter-clockwise

independently, see Figure D.

Remove the HEPA filter 12 from the dust container by turn the dust container back cover

anticlockwise. see Figure E. Clean the filter and the various parts with lukewarm water. These

parts are not dishwasher safe.

Make the good parts dry, let the filter dry completely before you put it back.

Remove the cover on the back of the device and remove the filter, see Figure E1.

Clean the filter and cover with lukewarm water, allow the parts to dry completely before you put

it back. The vacuum cleaner and the other parts you can use a damp cloth to decline.

Never use the vacuum with a wet filter! This may cause an electric shock and

the unit may malfunction.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tristar sz 2187 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info