Bedienungsanleitung Triton MOF 001 (Seite 8 von 82) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch)

664979

Zoom out

Zoom in

Vorherige Seite

1/82

Nächste Seite

Troubleshooting

Problem Possible cause Solution

No function when Power Switch (12) is operated No power Check power supply

Defective On/Off Power Switch Replace the Power Switch at an authorised Triton service

centre

Inaccurate cutting proﬁle Depth Stop (4) not correctly adjusted Ensure that the Depth Stop corresponds to the maximum

amount of cut permitted by the Turret Stops (1)

Incorrectly ﬁtted or loose router bit/Collet (22) Tighten router bit/Collet and cutter assembly

Router will not operate No supply of power Check that power is available at source

Brushes worn or sticking Disconnect power, open Brush Access Covers (9) and ensure

brushes are not damaged or heavily worn

Power Switch (12) is faulty Have the tool serviced by an authorised Triton service centre

Motor components faulty or short circuited Have the tool serviced by an authorised Triton service centre

Router runs or cuts slowly Blunt or damaged cutter Re-sharpen or replace cutter

Speed Controller (15) set low Increase variable speed setting

Motor is overloaded Reduce pushing force on router

Excessive vibration Incorrectly ﬁtted or loose router bit Reﬁt or tighten router bit

Bent or damaged router bit Replace router bit

Heavy sparking occurs inside motor housing Brushes not moving freely Disconnect power, remove brushes, clean or replace

Damaged or worn motor Have the tool serviced by an authorised Triton service centre

Micro Winder (10) “clicks” or not adjusting Plunge Lock Lever (16) engaged Release Plunge Lock Lever (16)

Reached end of adjustment range Reset Micro Winder (10) and set depth with the Depth

Stop (4)

Makes an unusual sound Mechanical obstruction Have the tool serviced by an authorised Triton service centre

Damage to internal windings Have the tool serviced by an authorised Triton service centre

• Never use caustic agents to clean plastic parts. If dry cleaning is not sufﬁcient, a mild

detergent on a damp cloth is recommended

• Water must never come into contact with the tool

• Ensure the tool is thoroughly dry before using it

• If available, use clean, dry, compressed air to blow through the ventilation holes (where

applicable)

Lubrication

• Slightly lubricate all moving parts at regular intervals with a suitable spray lubricant

Brushes

• Over time the carbon brushes inside the motor may become worn

• Excessively worn brushes may cause loss of power, intermittent failure, or visible sparking

• To replace the brushes, remove the two Brush Access Covers (9). Remove the worn brushes

and ensure the sockets are clean. Carefully replace with new brushes and then replace the

Brush Access Covers

• After ﬁtting run the router without load for 2-3 minutes to help the brushes bed in. The

process of the brushes fully bedding in may take repeated uses. Motor sparking may

continue until new carbon brushes have bedded in

• Alternatively, have the machine serviced at an authorised service centre

Storage

• Store this tool carefully in a secure, dry place out of the reach of children

Disposal

Always adhere to national regulations when disposing of power tools that are no longer

functional and are not viable for repair.

• Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE),

with household waste

• Contact your local waste disposal authority for information on the correct way to dispose of

power tools

330085_Z1MANPRO1.indd 8 05/01/2017 15:35

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Triton MOF 001 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info