Bedienungsanleitung Triton T12OT (Seite 8 von 90) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch)

665059

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

Troubleshooting

Problem Possible cause Solution

Red LED does not illuminate and Battery (5) not charging Battery not fully seated Reﬁt Battery correctly

Battery Charger (11) not powered Recheck mains connection

Battery has low capacity Battery not being fully charged Wait until green LED is illuminated

Battery has been charged over 200 times and capacity has

started to reduce

This is normal for batteries. Contact your Triton dealer to

purchase a replacement battery

Tool cannot be switched on Battery discharged Recharge battery or replace with a charged battery

Defective battery Replace battery

Tool defective Contact your Triton dealer or authorised service centre

Tool stops operating during use Battery has low charge Charge battery fully before use especially before jobs that

are more difﬁcult to cut

Over temperature safety feature has operated Tool may require up to 30 minutes for tool to reset. A slower

speed setting may be required to prevent this safety feature

operating. Check Motor Vents (2) are not blocked. Reduce

the amount of hand pressure on the tool to reduce load

on the motor

Over current safety feature has operated Tool may require up to 1 minute to reset. A slower speed

setting may be required. Check Motor Vents are not blocked.

Reduce the amount of hand pressure on the tool to reduce

load on the motor

Blade not cutting correctly Speed setting low Increase speed

Material may not be suitable for blade Change blade

Material not suitable for tool Some materials including hardened metals have no

compatible blade

Blade may be worn Replace blade

allow dust, wood chippings and swarf to build up. Use a vacuum cleaner to keep the work

space clean, especially in conﬁned areas.

WARNING: DO NOT inhale dust. Wear adequate breathing protection. Some dusts may be

toxic especially from man-made composite materials.

Sawing

• Ensure the saw blade is sharp and in good condition

• Do not use saw blades that are damaged or deformed in any way

• When sawing light building materials, follow the recommendations of the material suppliers

• Apply plunge cuts to soft materials ONLY, for example, wood, gypsum plasterboard etc.

(image F)

• If using saw blades not designed for cutting metal, ensure there are no nails or screws

embedded in the workpiece. If necessary, remove embedded objects or use metal cutting

saw blades instead

Sanding

• The removal rate and the sanding pattern are determined by the type of sanding sheet, the

preset oscillation rate and the applied pressure

• Pay particular attention to applying uniform sanding pressure; this increases the working

life of the sanding sheets

• Intensifying the sanding pressure will not lead to an increase of the sanding capacity, but to

increased wear of the machine and the sanding sheet

• For precise on-the-spot sanding of edges, corners and hard to reach areas, it is also

possible to work only with the tip or an edge of the sanding plate (Fig. G)

• A sanding sheet that has been used for sanding metal should not be used for sanding

other materials

• Regularly brush down or vacuum the surface being sanded to ensure the sanding sheet is

in direct contact with the surface

Scraping

• For scraping, select a high speed setting

• On soft surfaces (e.g. wood), work at a ﬂat angle and apply only light pressure so that the

scraper does not cut into the surface

Accessories

A full range of accessories and products is available from your Triton stockist.

• T12B – T12 1.5Ah Li-Ion Battery 12V

• T12HCB – T12 Hi-Cap 3.0Ah Li-Ion Battery 12V

Additional Triton products compatible with the included batteries:

• T12CH – T12 Combi Hammer Drill 12V

• T12AD – T12 Angle Drill 12V

• T12DD – T12 Drill Driver 12V

• T12ID – T12 Impact Driver 12V

• T12RS – T12 Reciprocating Saw 12V

• T12FL – T12 Swivel Head Torch 12V

Spare parts can be purchased from your Triton dealer or online at www.toolsparesonline.com

Maintenance

WARNING: Always disconnect the battery from the tool before attaching or removing

accessories, making any adjustments or performing maintenance.

• This tool is manufactured using class-leading components and uses intelligent circuitry that

protects the tool and its components. In normal use it should provide a long working life

Cleaning

• Keep your machine clean at all times. Dirt and dust will cause internal parts to wear quickly,

and shorten the machine’s service life. Clean the body of your machine with a soft brush or

dry cloth. If available, use clean, dry, compressed air to blow through the ventilation holes

Storage

• Store this tool and its accessories after use in its case, in a dry, secure place out of the

reach of children

Disposal

Always adhere to national regulations when disposing of power tools that are no longer

functional and are not viable for repair.

• Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE),

with household waste

• Contact your local waste disposal authority for information on the correct way to dispose of

power tools

103691_Z1MANPRO.indd 8 31/08/2016 11:16

Triton T12OT Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info