Bedienungsanleitung Triton TA 184CSL (Seite 6 von 71) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

665060

Zoom out

Zoom in

Vorherige Seite

1/71

Nächste Seite

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may affect the power

tool’s operation. If damaged, have the power tool

repaired before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to

be performed. Use of the power tool for operations

different from those intended could result in a

hazardous situation.

4) S e r vic e

a) Have your power tool serviced by a qualiﬁed repair

person using only identical replacement parts.

This will ensure that the safety of the power tool is

maintained.

ADDITIONAL SAFETY FOR CIRCULAR SAWS

WARNINGS. Before connecting a tool to a power

source (mains switch power point receptacle,

outlet, etc.) be sure that the voltage supply is the same

as that speciﬁed on the nameplate of the tool. A power

source with a voltage greater than that speciﬁed for the

tool can result in serious injury to the user, and damage

to the tool. If in doubt, do not plug in the tool. Using a

power source with a voltage less than the nameplate

rating is harmful to the motor.

• Do not allow anyone under the age of 18 years to

operate this saw

• Ensure all supports and power cables are completely

clear of the cutting path

• Be aware that the blade will project from the underside

of the workpiece

• Do not reach beneath the workpiece where the guard

cannot protect you from the blade

• Regularly check the operation of the blade guard. If the

guard does not automatically cover the blade, have the

saw repaired before use

• Do not attempt to cut material thicker than detailed in

the Speciﬁcations section of this manual

• Ensure that work is correctly supported. Large panels

may sag under their own weight and bind the saw

blade. Supports must be placed under the panel on

both sides, close to the line of cut and near the edge of

the panel

• Do not apply any sideways or twisting force to the

blade whilst cutting

• Do not move the saw backwards at any time whilst

cutting

• If a cut does not extend to the edge of the workpiece,

or if the blade binds in the cut, allow the blade to come

to a complete stop and lift the saw out of the workpiece

• When operating the saw, use safety equipment

including safety goggles or shield, ear protection, dust

mask and protective clothing including safety gloves

• Note the direction of rotation of the motor and the blade

• Beware of projected waste. In some situations, waste

material may be projected at speed from the cutting

tool. It is the users responsibility to ensure that

other people in the work area are protected from the

possibility of projected waste

• Ensure hands are away from the cutting area and

blade. Keep one hand on auxiliary handle, or motor

housing. If both hands are holding the tool they cannot

be cut by the blade

• Inspect the workpiece and remove all nails and other

embedded objects prior to starting work

• Adjust the cutting depth to the thickness of the

workpiece i.e. less than a full tooth of the blade should

be visible below the workpiece

• Do not attempt to free a jammed blade before ﬁrst

disconnecting the machine from power

• Always secure the workpiece to a stable platform,

ensuring that body exposure is minimised, avoiding

blade binding or loss of control

• Always stand to one side when operating the saw

• Never hold a workpiece in your hand or across your

legs whilst cutting

• If you are interrupted when operating the saw,

complete the process and switch off before looking up

• Power tools must always be held by the insulated

gripping surfaces when performing an operation,

ensuring protection if the cutting tool makes contact

with its own cord or hidden wiring. Contact with a ‘live’

wire will make exposed metal parts of the power tool

‘live’ and shock the operator if the insulated gripping

surfaces are not used

• For accuracy of cut, and to avoid blade binding, always

use a rip fence or straight edge guide

• Always use recommended blades with correct size and

shape of arbor holes e.g. diamond or round. Blades that

do not match the mounting hardware of the saw will

run eccentrically, causing loss of control

• The blade bolt and washers were specially designed

for this tool. For optimum performance and safety of

operation never use damaged or incorrect bolt/blade

washers

Safety Instructions

330130_Z1MANPRO.indd 6 11/07/2014 10:45

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Triton TA 184CSL Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info