Bedienungsanleitung Triton TA1200BS (Seite 7 von 82) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch)

665069

Zoom out

Zoom in

Vorherige Seite

1/82

Nächste Seite

6. The Backstop may be ﬁxed in a raised position or almost level with the sanding belt. Ensure

that the Backstop is not in contact with the sanding belt

7. Fit dust extraction system or the Dust Bag (10)

8. Turn on the sander and use the lock-on button to keep the sander running

9. Check solidity of ﬁxing and alignment of sanding belt whilst running the sander. If

necessary, turn off and reﬁx the sander

WARNING: DO NOT use the sander inverted unless it is securely clamped to the work surface.

Fitting the optional sanding frame (TBSIS)

• The sanding frame helps to control depth of cut and prevents tilting and gouging

1. Use the Inversion Clamps (15) to secure the belt sander on a solid, ﬂat, level work surface in

an inverted position (Image I)

2. Place the Sanding Frame (18) over the sander so that, with the smooth surface of the frame

uppermost, the ﬁxing positions on the frame correspond with the ﬁxing positions on the

sander (Image J)

3. Insert the Frame Locking Knobs (20) on the side where there are two ﬁxing positions then

tighten to secure the frame, but allow for a small amount of movement

4. Insert the Depth Plate Locking Knob (19) in the single ﬁxing position (on the opposite side to

the frame locking knobs). Align the depth calibrations with the scale pointer at the position

required

Note: For minimum sanding depth, align with calibration furthest from the frame surface

(see above)

5. Use a level to check the frame is horizontal, then tighten the Frame Locking Knobs fully to

secure the frame ready for use

Using the sanding frame

• We recommend that you begin by sanding against the grain

• Start the sander facing at 10 or 11 o’clock, and move it back and forth across the

workpiece slowly. Finish by sanding parallel to the grain

Accessories

• A full range of different grit sanding belts and accessories is available from your Triton

stockist. Spare parts can be obtained from toolsparesonline.com

Maintenance

WARNING: Always disconnect from the power supply before carrying out any inspection,

maintenance or cleaning.

Emptying the dust bag (if ﬁtted)

WARNING: Always switch off and disconnect from the power supply before detaching the dust

extraction system.

1. To remove the Dust Bag (10), rotate outwards to disengage the bayonet, then pull off (Image

2. Open the bag, empty and reﬁt (see ‘Connecting the dust extraction system’)

Note: If the sanding dust contains harmful substances, such as particles from old paint,

varnish, surface coatings etc, always dispose of according to laws and regulations.

WARNING: For optimum dust removal, empty the Dust Bag when it is no more than half full.

Note: Always clean the tool THOROUGHLY when switching from sanding wood to sanding

metal and vice versa.

General inspection

• Regularly check that all the ﬁxing screws are tight. They may vibrate loose over time

• Inspect the supply cord of the tool, prior to each use, for damage or wear. Repairs should

be carried out by an authorised Triton service centre. This advice also applies to extension

cords used with this tool

Cleaning

• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly,

and shorten the device’s service life. Clean the body of your machine with a soft brush, or

dry cloth. If available, use clean, dry, compressed air to blow through the ventilation holes

(where applicable)

Lubrication

• Slightly lubricate all moving parts at regular intervals with a suitable spray lubricant

Changing the drive belt

Note: A spare drive belt is supplied with the sander. Further replacements and other spare

parts are available from your Triton stockist or from toolsparesonline.com.

1. Using a Phillips screwdriver, remove the screw holding the Drive Belt Cover (5) in place

2. Remove the worn belt by easing it off the bottom larger drive pulley, and then lift away

3. Clean all dust and debris away

4. Place new drive belt over the top drive pulley and push onto the larger pulley, then rotate

the belt until it is on both pulleys and located in the grooves of each pulley

5. Place the Drive Belt Cover back on and screw the ﬁxing screw tight

Storage

• Store this tool carefully in a secure, dry place out of the reach of children

Disposal

Always adhere to national regulations when disposing of power tools that are no longer

functional and are not viable for repair.

• Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE),

with household waste

• Contact your local waste disposal authority for information on the correct way to dispose of

power tools

330125_Z1MANPRO1.indd 7 17/01/2017 17:26

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Triton TA1200BS Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info