Bedienungsanleitung Triton TCMPL (Seite 8 von 82) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch)

665074

Zoom out

Zoom in

Vorherige Seite

1/82

Nächste Seite

Maintenance

WARNING: Always disconnect from the power supply before carrying out any

maintenance/cleaning.

• Inspect the supply cord of the tool, prior to each use, for damage or wear.

This advice also applies to extension cords used with this tool

• if the replacement of the supply cord is necessary, this has to be done by the

manufacturer or his agent in order to avoid a safety hazard

Cleaning

1. Keep the tool’s air vents unclogged and clean at all times

2. Regularly check to see if any dust or foreign matter has entered the grilles

near the motor and around the On/Off switch. Use a soft brush to remove

any accumulated dust. Wear safety glasses to protect your eyes whilst

cleaning

3. Re-lubricate all moving parts at regular intervals

4. If the body of the planer needs cleaning, wipe it with a soft damp cloth. A

mild detergent can be used but do not use alcohol, petrol or other cleaning

agent

5. Never use caustic agents to clean plastic parts

CAUTION: Water must never come into contact with the planer.

Drive belt replacement

CAUTION: Always ensure that the tool is switched off and unplugged from the

power supply before making adjustments or installing or removing blades. Also

ensure planer is in park and during belt replacement keep hands well away

from the blade barrel area. It is also suggested that you wear leather gloves to

change the belt in case you make contact with the blades.

1. To replace the drive belt ﬁrst take out the three cross-head screws that

secure the drive belt cover on the left-hand side of the planer as viewed

from the rear

2. Remove the damaged belt and use a soft brush to clean the pulleys and the

surrounding area

NOTE: Wear eye protection when cleaning

3. With the three continuous ‘v’ proﬁles on the inside, place the new belt over

the bottom pulley. Half ﬁt the other end of the belt on the top pulley then roll

the belt in place whilst turning the pulley

4. Check that the belt runs evenly by manually turning the belt

5. Replace the cover and the three ﬁxing screws

6. Replace the electrical plug and run the planer for a minute or two to make

sure that the motor and belt are operating correctly

General Inspection

Regularly check that all the ﬁxing screws are tight. They may vibrate loose

Storage

• Store this tool and its accessories after use in its case, in a dry, secure place

out of the reach of children

Disposal

Always adhere to national regulations when disposing of power tools that are

no longer functional and are not viable for repair.

• Do not dispose of power tools, or other waste electrical and electronic

equipment (WEEE), with household waste

• Contact your local waste disposal authority for information on the correct

way to dispose of power tools

773123_Z1MANPRO1.indd 8 12/01/2017 14:31

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Triton TCMPL Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info