Bedienungsanleitung Triton TRPUL (Seite 8 von 98) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch)

665075

Zoom out

Zoom in

Vorherige Seite

1/98

Nächste Seite

Parallel Fence Guide

1. Fit the Parallel Fence Guide (23) using the ﬁxing angle and the

Parallel Fence Attachment Knob (22) (Image H)

2. When set at right angles to the planer base, the fence provides

a guide to help control the planing action

Operation

Switching ON & OFF

WARNING: Before plugging the machine into the power socket always check

that the ON/OFF Trigger Switch (5) and Lock-Off Button (6) work properly.

1. Plug in the tool and grip the tool with index ﬁnger on the ON/

OFF Trigger Switch and thumb on the Lock-Off Button

2. With the rest of your hand gripping the tool, depress the Lock-Off

Button with your thumb and squeeze the ON/OFF Trigger Switch. You

can release the Lock-Off Button once the planer has started

3. To stop the tool, release the ﬁnger hold on the ON/OFF Trigger Switch

4. In order to restart the tool, repeat steps 1–2

WARNING: Please note that the planer blades continue to turn for some

time after switching OFF the planer. Wait until the motor has completely

stopped before setting down the tool to prevent damage to the planer blades

or the surface. If you wish to rest the planer on its side, do not rest it on the

side with the vents to prevent dust or chips from getting into the motor.

5. When the planer is not to be used for a short period, set the depth control knob to

the ‘P’ position and rest the front of the planer on a block of wood to keep the base

clear of the surface. Ensure that the rear parking foot is down to protect blades

Adjusting the speed

• The speed of the drum can be adjust to suit the material being planed or sanded

• Use the Variable Speed Control (25) to adjust the speed for the job in hand

Note: For planing it is recommended to have the planer running at full speed to

obtain the cleanest possible result. When sanding, the speed should be set from

1–6. On ‘MAX’ (maximum speed) the unit will vibrate and be hard to hold.

Adjusting the depth of cut

1. Rotate the Depth Adjustment Dial (1) clockwise for a

deeper cut and anticlockwise for a shallower cut

2. The calibrations on the ring under the Depth Adjustment Dial indicate

the depth of cut. For example, when ‘1’ is next to the pointer on

the front of the planer, the depth of cut is approximately 1mm

3. If depth of cut is critical, plane a scrap piece of wood, measure

the difference in thickness and adjust the setting as needed

Planing

WARNING: Moving the tool too fast may cause a poor quality of cut and can damage

the blades or the motor. Moving the tool too slowly may burn or mar the cut. The

proper feed rate will depend on the type of material being cut and the depth of the

cut. Practice ﬁrst on a scrap piece of material to gauge the correct motion.

WARNING: Always use two hands to hold the planer.

WARNING: Where possible, clamp the workpiece to a workbench.

1. Rest the front of the planer on the workpiece, ensuring the

blades are not in contact with the workpiece

2. Switch ON the tool and wait for the blades to reach full speed

3. Move the planer gently forward, applying pressure on the front of the tool at the start

of planing, and pressure at the rear of the tool towards the end of the planing stroke

Note: As a feature this planer has been ﬁtted with a larger front handle than traditional electric

planers. The front handle provides for good ergonomics when planing, allows the operator

to balance and control the unit with ease and is particularly useful when vertical planing.

4. Push the planer beyond the edge of the workpiece without tilting it downwards

Note: Planing is easier if you incline the workpiece slightly

away from you so that you plane ‘downhill’.

5. The rate of planing and the depth of cut determine the quality of the ﬁnish. For

rough cutting, you can increase the depth of cut; however, to achieve a good ﬁnish,

you will need to reduce the depth of cut and advance the tool more slowly

6. In between operations, you can rest the planer on a ﬂat surface with the

Rear Parking Foot (19) hinged down to support the planer so that the blades

are kept clear of the surface. Ensure the rear parking foot has been moved

across from the locked position (for transit) to the automatic position

Chamfering

1. To make a chamfered cut (Fig. I), align the ‘V’ groove (Fig. II) in the

front base of the planer with the corner edge of the workpiece

2. Run the planer along the corner edge

Full/unlimited rebating

• The planer has an unlimited rebating capability. When operating the

planer to achieve a full rebate, adhere to all instructions below.

1. With the hand gripping the Front Handle (2), use the thumb to push the

Drum Guard Release Lever (3) down to raise the Drum Guard (17), which

will expose the Blade Drum (16). This enables full unlimited rebating

2. Run the planer along the workpiece

3. Once you have ﬁnished planing the section, take the pressure off the Drum Guard

Release Lever and check the Drum Guard fully covers the blade drum

WARNING: DO NOT raise the drum guard if you are not

performing a full/unlimited rebate application.

WARNING: If the drum guard does not close completely, stop using the tool

immediately and have the unit serviced by a qualiﬁed service technician. If

you use the product with a defective blade drum guard, the manufacturer

will not be held liable for any damage or personal injury caused.

Note: Do not apply too much force on the lever. Excess

pressure may cause blade guard to break.

Sanding

• To use this tool as a sander, ﬁt the sanding drum and sleeve

designed for this tool. See ‘Fitting the Sanding Drum’

• Replacement sanding sleeves are available from your Triton stockist (part no. TRPSS)

• Wear safety goggles, a dust mask and earmuffs

1. Check that the Sanding Drum and sanding sleeve are in good conditions and ﬁxed securely

IMPORTANT: Set the planing Depth Adjustment Dial (1) to the ‘O’ height setting.

2. Use the Variable Speed Control (25) to set an appropriate speed 1–6.

Do not use MAX setting as this will cause the sander to vibrate

3. Depress the Locke-Off Button (6) and squeeze the ON/OFF Trigger Switch (5). Allow the

motor to reach the set speed before bringing the sander into contact with the workpiece

4. Sand with the grain, in parallel overlapping strokes

5. Adjust the variable speed dial as required

6. To remove paint of smooth very rough wood, sand across the grain at

45° in two directions, and then ﬁnish the parallel with the grain

7. Lift the sander OFF the workpiece before switching it OFF

WARNING: Remember to keep your hands away from the moving sanding drum;

it will continue to move for a short time after the tool has been switched OFF.

Note: After sanding with a drum sander, use of an orbital sander is

recommended to achieve a smoother ﬁnished surface.

Dust/shavings extraction

1. Connect the Dust/Chip Adaptor Tube (21) to the Dust/Chip Extraction Port (10)

2. The adaptor tube can be installed to allow shavings to ﬂow

either to the left or to the right of the workpiece

3. Use the Dust Diverter Guide Switch (9) to select the Dust/Chip Extraction

Port. Swing the lever across to close the port you do not want to use

4. A workshop dust extraction system or a household vacuum cleaner can

be connected to the adaptor tube for the efﬁcient removal of dust and

shavings, permitting a safer and cleaner working environment

Maintenance

WARNING: Ensure the tool is switched OFF and the plug is removed from the

power supply before making any adjustments or maintenance procedures.

General inspection

• Regularly check that all the ﬁxing screws are tight. They may vibrate loose over time

• Prior to each use, inspect the supply cord of the tool for damage or wear.

This advice also applies to extension cords used with this tool

• If replacement of the supply cord is necessary, this must be done by the

manufacturer or their agent in order to avoid a safety hazard

Drive belt replacement

• It is suggested that you wear leather gloves to change the

belt in case you make contact with the blades

1. To replace the drive belt, take out the ﬁve crosshead screws that secure the

drive belt cover on the left side of the planer when viewed from the rear

2. Remove the damaged/worn belt and use a soft brush to

clean the pulleys and the surrounding area

Note: Wear eye protection when cleaning out the pulley area.

3. With the four continuous ‘V’ proﬁles on the inside, place the new belt

over the bottom pulley. Half ﬁt the other end of the belt on the top

pulley then roll the belt in place while turning the pulley

837520_Manual .indd 8 28/02/2017 12:31

Triton TRPUL Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info