Bedienungsanleitung Triton TSPS450 (Seite 7 von 82) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch)

665086

Zoom out

Zoom in

Vorherige Seite

1/82

Nächste Seite

Sanding

WARNING: Do not sand metal with this sander. Sanding metal will cause sparks that may

ignite wood and dust particles on the sander or in the workshop

Note: The spindle rotates in an anti-clockwise direction

1. Check the machine is mounted securely on the workbench and the Spindle Lock Nut (6)

is fastened correctly with appropriate sanding sleeve and table insert, in accordance with

guidance in ‘Assembly’

2. Wear appropriate safety equipment, including face mask and safety glasses, then switch

on the dust extraction system (if available)

3. Turn the sander ON and allow the motor to reach full speed

IMPORTANT: Feed the workpiece gradually, AGAINST the direction of rotation, onto the sanding

sleeve. Failure to do this could force the workpiece away from the sanding sleeve with risk of

injury. Do not force the workpiece or apply excessive force.

4. When ﬁnished, turn off the machine and disconnect from mains power

Accessories

• A range of accessories and consumables, including TSS80G, TSS150G, TSS240G Sanding

Sleeves are available from your Triton stockist. Spare parts can be obtained from

toolsparesonline.com

Maintenance

WARNING: Ensure the tool is switched off and the plug is removed from the power point

before making any adjustments or carrying out maintenance.

• Any damage to this tool should be repaired and carefully inspected before use, by qualiﬁed

repair technician

• Have your power tool serviced by a qualiﬁed repair technician using only identical

replacement parts. This will ensure that the safety of the power tool is maintained

General Inspection

Regularly check that all the ﬁxing screws are tight. They may vibrate loose over time.

Power Cord Maintenance

If the supply cord needs replacing, the task must be carried out by the manufacturer, the

manufacturer’s agent, or an authorised service centre in order to avoid a safety hazard.

Cleaning

1. Remove dust and dirt regularly. Frequently blow or vacuum dust away from all sander

parts and the motor housing

2. Periodically remove the table insert and lower washer from the spindle and remove any

dust accumulation in the table insert area

3. Re-lubricate all moving parts at regular intervals

4. Never use caustic agents to clean plastic parts

Do not use cleaning agents to clean the plastic parts of the tool. A mild detergent on a damp

cloth is recommended. Water must never come into contact with the tool.

Storage

• Store this tool carefully in a secure, dry place out of the reach of children. If the tool is

permanently setup in a workshop or garage ensure access is restricted to prevent children

operating the tool.

Disposal

Always adhere to national regulations when disposing of power tools that are no longer

functional and are not viable for repair.

• Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE),

with household waste

• Contact your local waste disposal authority for information on the correct way to dispose of

power tools

516693_Z1MANPRO1.indd 7 30/08/2016 16:28

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Triton TSPS450 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info