Bedienungsanleitung Triton TWSS10 (Seite 9 von 134) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch)

665091

Zoom out

Zoom in

Vorherige Seite

1/134

Nächste Seite

Grinding Angle Set-Up Jig (TWSGAJ)

For setting up the correct angle for sharpening. Enables repeated accurate grinding of speciﬁc

bevel angles. (For usage instructions, see ‘Using the Grinding Angle Set-Up Jig’.)

Scissors Jig (TWSSJ)

2 1

5 4

Restores sharp edges to blunt scissors and garden shears. Twin clamps for securing blades.

Scissors Jig Familiarisation

1. Jig Support Plate

2. Scissor Clamp Holder

3. Scissor Clamp

4. Clamp Thickness Screw

5. Jig Tightening Knob

Using the Scissors Jig:

• The Scissor Clamp Holder (2) is ﬁtted with 2 Scissor Clamps (3). Normally, only the Scissor

Clamp on the right is required; however, for large scissors or shears the other clamp can

also be used

• Adjust the Scissor Clamp/s to ﬁt the scissor blade thickness. Loosen the Jig Tightening

Knob (5) then the Clamp Thickness Screw (4). Insert the scissor blade and re-tighten

• The Jig Support Plate has a surface designed to allow the jig to move easily while

sharpening

IMPORTANT: DO NOT use the Leather Honing Wheel to remove the burr from the scissor blade

after using the Grindstone. To remove the burr, draw the scissor blade through the grain at the

end of a piece of wood.

Note: Portable electric-planer blades (not tungsten carbide blades) are ground in the same way

as scissor blades; however, honing using the Leather Honing Wheel is required.

Setting the bevel edge angle

• The scissors’ bevel edge angle is set by adjusting the Jig Support Plate. Either repeat the

existing angle or create a new bevel edge angle by using the Grinding Angle Set-Up Jig

The same bevel edge angle:

1. Slide the Jig Support Plate (1) onto the Support Arm and tighten

2. Use a black marker pen to colour the bevel edge of scissor blade; rest the jig on the Jig

Support Plate with the scissors’ bevel edge touching the grinding wheel; and, using your

hand, turn the grinding wheel a quarter turn

3. Check the bevel edge to see what part of the black pen mark has been scratched off, then

adjust the Jig Support Plate to correct the angle

4. Re-test the quarter-turn scratch and re-adjust the Jig Support Plate if required

A new bevel edge angle:

1. Slide the Jig Support Plate onto the Support Arm and tighten

2. Use the Grinding Angle Set-Up Jig to set-up the Scissor Jig at the new angle (see ‘Using the

Grinding Angle Set-Up Jig’)

Support Arm Extension (TWSSAE)

Attaches to support arm. Provides simultaneous tool support above the grindstone and honing

wheels.

Carving Tool Jig (TWSCTJ)

For accurate sharpening of carving tools and other short tools. Clamps narrow and butt chisels

ﬁrmly. Internal ‘V’ shape automatically centres the tool.

Using the Carving Tool Jig:

1. Loosen the knob on the clamp and insert the appropriate chisel

2. Tighten the clamp’s knob

3. Use the Grinding Angle Set-Up Jig (see ‘Using the Grinding Angle Set-Up Jig’) and Support

Arm distance from the Grindstone to set the existing bevel edge grinding angle or a new

angle, if desired

4. Run the Whetstone Sharpener and frequently check the grind until the desired edge is

achieved

5. After grinding, use the Leather Honing Wheel and the Proﬁled Leather Honing Wheel

(TWSLHW optional accessory. See ‘Proﬁled Leather Honing Wheel’ for more information)

Note: Use the Stone Grader (see ‘Using the Stone Grader’) to change between rough or ﬁne

grading of the Grindstone, depending on how much grinding and sharpening is required.

Note: You may need use the Leather Honing Wheel to remove the burr frequently during the

grinding process so that the progress of the sharpening operation can be seen clearly.

IMPORTANT: You must use the same angle on the Leather Honing Wheel that was used on

the Grindstone. Adjust the Support Arm to set the same angle. Use a black marker pen to see

where the leather makes contact with the carving tool by colouring in the bevel edge and

moving the Leather Honing Wheel in the correct direction by hand for a couple of rotations.

Check where the marker has worn away then adjust the Support Arm accordingly.

Note: The Support Arm Extension (TWSSAE) is ideal for use with the Carving Tool Jig because

there is no need to change the Support Arm. Access to the Grindstone and the Leather Honing

Wheel is at same time with the Support Arm Extension (see ‘Support Arm Extension’ in

‘Accessories’ for more information).

949257_Z1MANPRO2.indd 9 16/03/2016 16:53

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Triton TWSS10 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info