Bedienungsanleitung Triton TWSS10 (Seite 12 von 134) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch)

665091

Zoom out

Zoom in

Vorherige Seite

1/134

Nächste Seite

Pre-Dressed Coated Grindstone

(TWSDW)

High-grade grindstone that sharpens steel edges efﬁciently and reliably. This is a replacement

Grindstone for the existing Grindstone. (See ‘Fitting the Grindstone and Water Trough’ for ﬁtting

instructions.)

Machine Cover (TWSWSC)

Keeps dust and dirt off the Whetstone Sharpener when not in use.

IMPORTANT: Always ensure the Whetstone Sharpener is switched OFF and unplugged before

ﬁtting the machine cover.

Note: Always empty the water from the trough after use. Never leave the Grindstone sitting in

water when not in use.

• Clean the Machine Cover by wiping over the outside with a damp cloth dampened with

warm, soapy water

Maintenance

General inspection

• Regularly check that all the ﬁxing screws are tight. They may vibrate loose over time

• Inspect the supply cord of the tool, prior to each use, for damage or wear. Repairs should

be carried out by an authorised Triton service centre. This advice also applies to extension

cords used with this tool

Cleaning

• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and

shorten the machine’s service life. Clean the body of your machine with a soft brush, or dry

cloth. If available, use clean, dry, compressed air to blow through the ventilation holes

Grindstone maintenance

• Do not use a grindstone that has received a blow, especially to the side of the stone

• Replace a cracked or suspect stone immediately

• Maintain an even grinding surface. Use the Diamond Trueing Tool TWSDTT (available

separately) to restore the grinding stone’s surface when it has become uneven or shows

other signs of wear

• See ‘Fitting the grindstone and water trough’ for guidance on ﬁtting a stone

Note: The spindle features a reverse thread: turn clockwise to loosen, anti-clockwise to tighten.

Replacing the leather honing wheel

If the Leather Honing Wheel (1) becomes worn or torn, it must be replaced:

1. Unscrew and set aside the Locking Knob (3)

2. Remove the worn honing wheel from the spindle, and position new wheel in its place

3. Re-ﬁt the Locking Knob and tighten.

Note: Tighten by hand only.

Storage

• ALWAYS empty the water trough, clean the machine and cover for storage

• NEVER store the machine with a wet or damp grinding stone. ALWAYS ensure the stone has

dried completely before covering and storing long-term

• Store this machine carefully in a secure, warm, dry place out of the reach of children

Disposal

Always adhere to national regulations when disposing of power tools that are no longer

functional and are not viable for repair.

• Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE),

with household waste

• Contact your local waste disposal authority for information on the correct way to dispose of

power tools

949257_Z1MANPRO2.indd 12 16/03/2016 16:53

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Triton TWSS10 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info