665078
22
Zoom out
Zoom in
Vorherige Seite
1/96
Nächste Seite
2. Loosen the hex screw located at the infeed end of the Kerf Plate (25), and use the Kerf Plate Access Hole (22) to
release the plate, Fig. F
3. Install the new Kerf Plate and/or Sacrificial Plate
4. Level the Kerf Plate, see ‘Kerf plate levelling’ for detailed instructions
5. Reinstall the Blade Guard
Cleaning
Keep the machine clean at all times. Dirt and dust will cause internal parts to wear quickly, and shorten the
machine’s service life. Clean the body of your machine with a soft brush or dry cloth. If available, use clean, dry,
compressed air to blow through the ventilation holes
Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a mild detergent on a damp cloth
is recommended
Water must never come into contact with the tool
Ensure the tool is thoroughly dry before use
Clearing debris blockages
1. Switch the tool ‘off’ and disconnect from the power supply. Detach the Blade Guard (3) from the Riving Knife (6) by
removing the screw securing the guard to the Riving Knife
2. Loosen the hex screw located at the infeed end of the Kerf Plate (25), and use the Kerf Plate Access Hole to
release the plate, Fig. F
3. Remove the Dust Chute Panel (12) and any vacuum connections connected to the Dust Extraction Port (9)
4. Locate and clear the debris blockage
5. Reinstall the Blade Guard, Kerf Plate, Dust Chute Panel and any vacuum connections once the blockage has been
cleared
Lubrication
Lubricate all moving parts with PTFE spray at regular intervals, especially after heavy use or cleaning
WARNING: DO NOT lubricate with oil or silicone-based maintenance sprays. Lubricant residue will combine with wood
and dust, leading to dirt build-up, which may interfere with moving parts and mechanisms. Dry lubricate ONLY, using
PTFE spray.
Storage
Store this tool and its accessories after use in its case, in a dry, secure place out of the reach of children
Disposal
Always adhere to national regulations when disposing of power tools that are no longer functional and are not viable
for repair.
Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE), with household waste
Contact your local waste disposal authority for information on the correct way to dispose of power tools
7
255671_Z1MANPRO1.indd 7 23/11/2016 10:38
22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

triton-twx7cs001

Suche zurücksetzen

  • Gibt es auch eine Bedienungsanleitung für TWX7CS002 in DEUTSCH? Eingereicht am 10-9-2023 14:54

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Triton TWX7CS001 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info