Bedienungsanleitung Tronic KH 3002 (Seite 10 von 14) (Englisch)

464846

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

- 8 -

Possible faults in the event of

non-functionality

• If neither of the two LEDs, 5 and 6, light up after

switching on, then the 10 amp fuse 7 on the

Energy Station might have blown. Changing fuses

is described in more detail in the section "Fuses".

• Should an LED light up on the Energy Station after

switching on, but the appliance fails to work, im-

mediately switch the Energy Station off. Check to

ensure that the cable is correctly connected –

and that “Positive” and “Negative“ have not

been switched. If required, also check the fuse in

your appliance, as described in its operating

instructions.

Power supply over the screw

connections

Caution!

Before performing any connections, always check

to ensure that both the appliance to be supplied

and the Energy Station are switched off. Place the

main switch 2 in the “OFF” position (centre position).

In this way you can avoid damage through connec-

tion faults.

Use the screw connections 9 at the rear of the ap-

pliance for 12V appliances requiring a high starting

current for switching on, but which do not otherwise

consume more than 10 A per hour.

Appliances with a high starting current could be for

instance ...

- 12 V vacuum cleaners

- 12 V drilling machines

- 12 V television sets etc.

Although these may not require more than 10 A

in operation, the fuse will immediately blow when

they are switched on. In this case such appliances

cannot be operated on the 12 V/10 A socket 3.

Operate these appliance only by way of the screw

connections 9, as described here.

Carrying out connections using the

banana plugs

1. The screw connections 9 are hollow, to accom-

modate so-called “banana plugs”. If such are

provided on your appliance cable, you can insert

these in the screw connections 9 from the top,

instead of screw-connecting.

Danger!

Extremely high current flows are possible here, ones

that are even capable of heating thick cables to red

hot! Before connecting, check to ensure that the

connecting cable for the appliance to be powered

is suitable for such a connection, so as to avoid

electric shock and the risk of fire.

These high currents are required for the starting of

some appliances. The screw connections 9 are

therefore neither routed by way of a fuse and nor

by way of the main switch 2, i.e. voltage is

continuously present!

For this reason it is imperative to ensure that a short-

circuit cannot be created at the screw terminals,

not under any circumstances!

Carrying out connections with the

bare ends of fixed appliance cables

1. If the cable is permanently connected with the

appliance to be powered, you can simply con-

nect the bare “Positive“ wire (usually red) to the

red screw connector 9.

2. Connect the bare "Negative" wire (usually black

or blue) to the black screw terminal 9.

To do so, unscrew the plastic caps on the screw

terminals 9. Clamp the bare wires underneath

when retightening.

Carrying out connections over a loose

cable

1. If the cable is not permanently connected to the

appliance being powered, but has a bare ap-pli-

ance plug available, first insert the appliance

plug in the socket on the appliance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tronic KH 3002 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Tronic KH 3002

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info