Bedienungsanleitung Trotec AW20S (Seite 5 von 12) (Englisch)

689442

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

EN 5

air washer AW 20 S

Transport and storage

Note

If you store or transport the device improperly, the

device may be damaged.

Note the information regarding transport and storage of

the device.

Transport

Before transporting the device, observe the following:

• Switch off the device.

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

• Check whether the upper and lower part of the device are

firmly interconnected.

• Lift the device at the lower part.

After transporting the device, observe the following:

• Set up the device in an upright position after transport.

Storage

Before storing the device, proceed as follows:

• Empty and clean the water tank prior to storage (see

chapter Maintenance).

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

When the device is not being used, observe the following

storage conditions:

• dry and protected from frost and heat

• in an upright position where it is protected from dust and

direct sunlight

• with a cover to protect it from invasive dust, if necessary

Assembly and installation

Scope of delivery

• 1x Device

• 1x Easy Kit cleaning brush

• 1x Manual

Unpacking the device

1. Open the cardboard box and take the device out.

2. Completely remove the packaging.

3. Fully unwind the power cable. Make sure that the power

cable is not damaged and that you do not damage it during

unwinding.

Start-up

• Before restarting the device, check the condition of the

power cable. If there are doubts as to the sound condition,

contact the customer service.

• Set the device up in an upright and stable position.

• Do not create tripping hazards when laying the power

cable or other electric cables, especially when positioning

the device in the middle of the room. Use cable bridges.

• Make sure that extension cables are unrolled completely.

Filling the water tank

1. Remove the upper part from the device and put it aside.

2. Remove the packaging from the disk.

3. Lift the disk out of the water tank.

4. Remove further packaging.

5. Refit the disk into the device.

6. Fill the water tank with fresh drinking water.

ð The filling level should not exceed the water level line in

the water tank.

7. Insert the SecoSan

stick (optional accessory) into the

lower part of the water tank.

8. Check whether the distance between the SecoSan

stick

and the disk is sufficient. The disk must be able to move

freely.

9. Place the upper part onto the water tank.

ð The display on the upper part and the logo on the lower

part should point in the same direction.

10. Check whether the upper and lower part are properly

interconnected as otherwise the device cannot be

switched on.

11. Plug the mains plug into a sufficiently fused mains socket.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec AW20S Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec AW20S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info