Bedienungsanleitung Trotec B500 (Seite 27 von 60) (Deutsch, Englisch, Französisch)

689444

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Operating Manual – Electronic Humidifier

B - 7

identically coded to the one sensor, or of operating each

one independently, each with a separate sensor and

different codings. Please proceed as follows.

Procedure:

1. Carefully lift the cover of the radio sensor with a

small screwdriver and take it off.

2. Code the radio sensor by setting the slide control

with a small screwdriver.

3. Remove the housing of the B 500 air humidiﬁer.

4. Loosen the four of screws on the top side of the con-

trol panel and lift it off.

5. Code the receiver circuit board on the rear side of

the control panel by setting the slide control with a

small screwdriver.

m The coding of the radio sensor and of the

receiver circuit board must match exactly

(note ON and OFF). Otherwise there is no

certainty that the system will function.

6. Close the cover of the radio sensor again.

7. Fasten the control panel down again with the four

screws and set the top part of the housing onto it.

8. Breathe lightly on the radio sensor to check the

functioning of the system

15. Fault code display

The B 500 Professional has an independent monitor-

ing system that gives you the possibility of spotting

errors quickly and reacting accordingly.

The fault display can be combined with an acoustic sig-

nal so that a „beep” can be heard in addition to the dis-

play being shown. You can select this setting yourself.

Please refer to the section on „Menu programming”.

The following fault codes tell you what problem has

occurred and what has to be done.

m If a fault code is displayed, only the On/Off

button and the PROG and SET key on the re-

mote control unit can be used.

Fault code Fault What to do?

01 Water tank is empty • Check water level and top up if necessary.

• Check water level diodes for dirt and clean if necessary.

• Has distilled water been used? If so, top up with plain tap

water.

• Check the diodes connection.

• Is the automatic water supply defective? (optional extra)

02 UV lamp defective • Replace UV lamp. (see „Changing the UV tube“)

03 Water leaking

(only possible with external

water sensor)

• Check whether the filter has been inserted correctly.

• Check whether the appliance is standing upright.

• Check whether the automatic water supply is working cor-

rectly (if fitted).

• Check tank for leaks.

04 Water tank overfilled

(only possible with automatic

water supply)

• Check the function of the magnetic valve.

• Check the water level diodes for dirt.

05 No radio signal from hygros-

tat. The receiver on the con-

trol panel has not received a

signal for a quite some time.

•Is the radio transmitter too far away from the appliance?

• Check the function and coding of the radio transmitter (see

„Starting up” / „Coding the radio sensor system”).

• Replace the batteries if necessary.

09 Several faults have occurred

simultaneously

• Check the appliance as described for Faults 01 to 04.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec B500 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info