756404
8
Zoom out
Zoom in
Vorherige Seite
1/18
Nächste Seite
8 EN
pyrometer controlled via smartphone BP21WP
Switching the multi-point laser on/ off
1. Briefly actuate the On/ off/ measurementbutton(3) at the
appSensor twice to switch on the multi-point laser.
2. Briefly actuate the On/ off/ measurementbutton(3) at the
appSensor two times again to switch the multi-point laser
off.
Info
Please note that the multi-point laser does not serve
for temperature measurements but is instead used as
aiming aid for the surface to be measured.
Carrying out a measurement
Info
Note that moving from a cold area to a warm area can
lead to condensation forming on the device's circuit
board. This physical and unavoidable effect can falsify
the measurement. In this case, the app will either
display incorrect measured values or none at all. Wait a
few minutes until the device has become adjusted to
the changed conditions before carrying out a
measurement.
1. Make sure that the surface to be measured is free of dust,
dirt or similar substances.
2. To be able to gain exact measurement results on surfaces
which reflect heavily, stick matt masking tape to the
surface or apply matt black paint with a very high and
known degree of emission.
3. Note the 10:1ratio of the distance to the measuring spot
diameter. For accurate measurements the measuring
object should be at least twice as large as the measuring
spot.
Individual value measurement
When the appSensor has been successfully connected to the
terminal device, an individual value measurement is started and
the first determined value will be indicated.
Sensors MEASUREMEN
TS
Reports CUSTOMERS SETTINGS
Refresh measured value
11
10
12
9
BP21WP
25,3 °C
Temperature[24,7 | 25,4] Ø 25 25,3 °C
No. Designation Meaning
9 Numeric value
display
Indicates the minimum, maximum and
average values for the temperature as
well as the current temperature value.
10 Refresh measured
value button
Performs an individual measurement
and refreshes the displayed values.
11 Menubutton Opens the menu for making settings
for the current measurement.
12 Numeric value
display
Indicates the most recently
determined temperature value.
Refreshing the measured value
Proceed as follows to refresh the measured values in the
individual value measurement mode:
1. Press the Refresh measured value button(10) on the
terminal device.
ðThe appSensor determines the current measured value
which is then displayed on the terminal device.
2. You can also press the On/ off/ measurement button(3)
on the appSensor.
ðThe appSensor determines the current measured value
which is then displayed on the terminal device.
8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Trotec BP21WP wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Trotec BP21WP

Trotec BP21WP Bedienungsanleitung - Deutsch - 18 seiten

Trotec BP21WP Bedienungsanleitung - Holländisch - 17 seiten

Trotec BP21WP Bedienungsanleitung - Französisch - 17 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info