753308
8
Zoom out
Zoom in
Vorherige Seite
1/13
Nächste Seite
8 EN
heat gun HyStream 200
Transport and storage
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Transport
Before transporting the device, observe the following:
Switch off the device.
Hold onto the mains plug while pulling the power cable out
of the mains socket.
Allow the device to cool down.
Allow the attachment nozzle to cool down.
Remove the attachment nozzle from the air outlet.
Storage
Before storing the device, observe the following:
Switch off the device.
Hold onto the mains plug while pulling the power cable out
of the mains socket.
Allow the device to cool down.
Allow the attachment nozzle to cool down.
Remove the attachment nozzle from the air outlet.
Clean the device as described in the Maintenance chapter.
When the device is not being used, observe the following
storage conditions:
dry and protected from frost and heat
Ambient temperature below 45°C
protected from dust and direct sunlight
Start-up
Unpacking the device
Take the device and the accessories out of the packaging.
Warning of electrical voltage
Electric shock from insufficient insulation.
Check the device for damages and proper functioning
before each use.
If you notice damages, no longer use the device.
Do not use the device when the device or your hands
are damp or wet!
Check the contents for completeness and look for
damages.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Dispose of the packaging material according to the
national regulations.
Using the attachment nozzles
Warning of hot surface
The insertion tool might still be hot after the
application. Burn hazard when touching the insertion
tool.
Do not touch the insertion tool bare-handed!
Wear protective gloves!
1. Affix the attachment nozzle best suited for the task at hand
to the air outlet.
2. Make sure that the attachment nozzle is plugged on all the
way and fits tightly.
Info
The device may be used with or without attachment
nozzle.
Connecting the power cable
1. Insert the mains plug into a properly secured mains
socket.
8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Trotec HyStream 200 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Trotec HyStream 200

Trotec HyStream 200 Bedienungsanleitung - Deutsch - 14 seiten

Trotec HyStream 200 Bedienungsanleitung - Holländisch - 13 seiten

Trotec HyStream 200 Bedienungsanleitung - Französisch - 14 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info