Bedienungsanleitung Trotec PAC 2000X (Seite 8 von 18) (Englisch)

688811

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

7 Operating manual – Local air conditioner PAC 2000 X EN

Setting the operating mode

• To set the operating mode, press the Functions button (2):

–cooling,

–heating,

– dehumidifying (drying).

Setting the temperature

• Use the temperature control buttons (+ (3) or - (4)) to set the

desired temperature.

Setting the fan speed

• Choose from the available speed levels by pressing the

button Speed (6).

–Low

–Medium

–High

–Auto

Note:

During dehumidification operation this button is disabled, since in

dehumidification mode the device can only be operated at low fan

speed.

If AUTO is selected during cooling operation, the device

automatically switches between the other three speed levels –

depending on the temperature difference between the set and the

actual ambient temperature.

Setting the timer

Timer on

TIMER ON is used to turn the device on automatically after the set

time has passed.

• Press the TIMER button (7) in stand-by to set the desired

time.

• Once the set number of hours has lapsed, the device will

switch on automatically.

• If you press the POWER button (1) before the time has

expired, the device will switch on and the set time will be

deleted.

• You can also determine the function and fan speed while

setting the timer.

Timer off

TIMER OFF is used to turn the device off automatically after the

set time has passed.

• Press the TIMER button (7) during operation to set the desired

time.

• Once the set number of hours has lapsed, the device will

switch off automatically.

• If you press the POWER button (1) before the time has

expired, the device will switch off and the set time will be

deleted.

Sleep control function

Note:

The sleep control function is only available in cooling mode.

• Press the SLEEP button (8) during cooling operation to set the

temperature. After one hour the temperature increases by

1 °C and maximally by 2 °C after 2 hours.

• Actuating the SLEEP button (8) again deactivates this setting.

Dehumidification operation (drying)

• The temperature cannot be regulated during

dehumidification operation, the fan speed is low.

• In dehumidification (drying) mode humidity is extracted from

the air and collected in an internal tank.

• Once the maximum filling level of the water tank is reached,

E4 or the ALARM warning light appears on the display.

• Drain the water tank when it is full. See Emptying the

condensation tank on page 11.

Discharging the condensate

• In dehumidification mode the rubber cap on the drain hole (1)

is to be removed and replaced by a proper drain pipe.

• Remove the exhaust air hose, connect a drain pipe to the

drain hole (1) and drain the water to enhance the

dehumidification capacity.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PAC 2000X Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PAC 2000X

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info